Search results

Can anyone tell me what is going on with this powerlogger file?

What are the options for an ignition control module? All I have read says the aftermarket ones are no good. Also may need a coilpak. Been chasing a gremlin for years & discovered that the wiring harness that connects to the ign module had 1 of the pins push the socked back in the connector...

BATTRY KELP RUNNING DOWN. THOUGHT IT WAS BAD, BUT FOUND THAT MY STOCK UNTOUCHED RADIO FACE PLATE IS LIT UP WITH KEY OFF. ANYONE EVER HAVE A PROBLEM LIKE THIS?

Need some feedback on this reading please. what would make car stumble @ wot?

need the long compressor bolt that goes thru the accessory bracket then thru the a/c compressor from the rear & threads into the bottom bolt hole of the pork chop looking bracket that the alternator mounts. the parts breakdown that I have does not show the bolt. Should be M10 1.50 thread &...

ANYONE KNOW THE SIZE OF THE BOLT THAT COMES THRU THE SUPPORT BRACKET THAT MOUNTS TO THE BOTTOM STUD OF THE DRIVER SIDE HEADER, GOES THRU THE BRACKET & THRU THE ACCESARY BRACKET THRU THE COMPRESSOR & THREADS INTO THE BOTTOM OF THE PORK CHOP LOOKING BRACKET ON THE FRONT OF THE COMPRESSOR. MINE...

Is there any way to slide the ac compressor forward to check the mounting bolts on the accessory mounting bracket? I do not want to remove the ac lines. I have the chirping noise at idle only & no noise when I start engine with belt off. I have already tested the alternator, tensioner pulley...

Does anyone know the voltages at the ignition switch for all the wires? I have a no crank issue & believe it may be the ignition switch. I posted all the info in the tech section & evidently that was the wrong forum. Any help greatly appreciated.

Razors alky, Ericks alky chip, powerlogger, scanmaster, Innovate wideband, after market Enforcer doorlock interface with alarm, also previous Enforcer pager alarm that has been removed. Car has worked perfect for years, Tried to start to get ready for summer & starter engaged then nothing...

looking for tensioner 87 gn

My low fuel-light will come on when the tank has plenty of fuel. Also,my seatbelt light will come on with the belts belted. Both these are speratic & dont seem to hurt performance. This is an original digital dash. any suggestions greatly appreciated.

Does anyone have a spare cd for power logger. My laptop crashed & I can"t find my original.

Can Another Guage Other Than The One That Comes With The Xd-16 Work On A Lc-1? I Bought The Lc-1 & Now Need A Guage & Have Not Been Able To Find A Guage Without Buying The Complete Setup. Need Guage Only That Will Work With Lc-1. Any Help Appreciated

I'll try once more, looking for electrical hookup instructions for 87 gn. Is there anyone on this forum that uses this controller on their gn? need help if someone has the info, would be greatly appreciated. the apexi instructions are all for imports.

Does anyone have a wiring diagrham for avc-r controller for gn installation. 87 with digital dash. Any help greatly appreciated

-------------------------------------------------------------------------------- I have a apexi avc-r, was told it was universal & now cannot find any wiring instructions. went to apexi web site & all their instructions are for rice burners. Is anyone running a avc-r? Need the wiring...

Dont know if this is the right forum for this. if not please let me know. I have a apexi avc-r, was told it was universal & now cannot find any wiring instructions. went to apexi web site & all their instructions are for rice burners. Is anyone running a avc-r? Need the wiring instructions if it...

trans was pulled & reinstalled for converter change. i have researched every board i can think of & need to know which port on the trans is the in & which is the out. thanks to my son, they were not marked when removed. research answers were about even split on which was which, so this thread is...