Search results

  1. 1000MileStylez

    1986 Buick Regal Street car

    1986 Buick Regal and whole lot of extras. Open to offers. Car weighs 3210lbs w/o driver Engine Machining performed by S-K Speed,Lindenhurst Long Island 109 block .020 over JE Forged Pistons Crower 4340 H beam rods Eagle crank internal balance Comp cams hydraulic roller 218/212 Morell...
  2. 1000MileStylez

    Cold start idle speed

    Have a 218/212 roller cam. Trying to get the car to idle properly using classic fast. What is a reasonable cold start idle speed?
  3. 1000MileStylez

    Checking engine timing with light. Fast b2b

    By miricle got the engine running somewhat. I think my timing is way off. I want to check the base reference angle. How do I go about doing this. Which screen should I be looking at while I’m checking the balancer and what mark on the balancer should I be looking at?
  4. 1000MileStylez

    setting lash on scorpion rockers and polylocks

    So i was setting the lash on my motor. I noticed on #1 cylinder I moved the pushrod up and down and turning while i tighten the poly lock down then i give it one full turn for preload with a ratchet and lock the set screw, then on 3# and #5 cylinder when i repeat the same procedure when i want...
  5. 1000MileStylez

    A body spindles on G body

    Last year i bought lowering spindles. I just purchased a kit with all the tierods. I found that the tierods dont fit the center link or i have them backwards and it doesnt fit the spindle. Could be they sold me the wrong center link. The upper and lower ball joint on the control arms appear and...
  6. 1000MileStylez

    Stock tail light wiring.

    Redoing my harness I'm questioning the wiring for the turn signal. Brakes. Could someone send me a cell phone video of how the light up? I'm having a hard time. Do the brake lights void the turn signal when you're braking? Are the small 194/168 bulbs parking lights only?
  7. 1000MileStylez

    Fuel pump/water pump wiring

    Race car guys do you have it wired to a switch where you manually turn it on with relay or do you have it wired to a relay and just come on when ignition switch is turned?
  8. 1000MileStylez

    Wtb 84-87 header panel

    Need a header panel. Can be a regal must be in good shape with all mounting studs in place.
  9. 1000MileStylez

    GM front cover with a Duttweiler pump

    GM front cover with a Duttweiler pump i had installed by TA performance. I decided to go a different route. So its up for grabs. I would like 500 for it obo . The front cover was never ran through a running motor. It was installed and removed. Pump still packed with grease. Never primed...
  10. 1000MileStylez

    Starter install issue

    After installing my faulty jw flex plate that needed to grind out a couple mounting holes I went to install my power master starter. Trouble is I don't have 1/16th or more distance away from the flexplate it's actually overlapping. I have the flexplate installed with the flat side towards...
  11. 1000MileStylez

    Belltech springs issue

    So i have belltech springs which drop the rear by 1.5". I have the QA1 single adjustable shocks in the rear but the rear drops too low when the car is raised and they fall out of the perch. Should i get different shocks? If you have a Qa1 part number too that would be help! I was also thinking...
  12. 1000MileStylez

    Looking for used pinion and spool bearings/races

    Need LM102949 and LM102910 bearings 2 of each. Also need used pinion bearings.
  13. 1000MileStylez

    Brushed stainless steel throttle brackets

    I made a few at work. $20 shipped Also have my GM front cover with Dutt oil pump $450 see post http://www.turbobuick.com/forums/threads/gm-front-cover-duttweiler-pump-for-sale.420731/
  14. 1000MileStylez

    GM front Cover + Duttweiler pump for sale

    This is i believe a GM front cover with a Duttweiler pump i had installed by TA performance a few months ago. I decided to go a different route. So its up for grabs. I would like 500 for it. The front cover was never ran through a running motor. It was installed and removed. Pump still packed...
  15. 1000MileStylez

    Duttweiller oil pump for newbies

    Trying to understand how the oil lines are routed. I know there are several threads about this pump but the one bit of info i cant find is where does the line run to after the oil filter. TA performance recommended -16 line from the pan to the "In" of the pump. -16 seems pretty large. Now in...
  16. 1000MileStylez

    What happened to the babes with buicks thread?

    Can someone post here it or did it get deleted?
  17. 1000MileStylez

    Timing sprocket to cam, bolt thread size

    I don't have the motor at my current location to measure. I do need new bolts. What is the thread size and does anyone recommend a ARP part # that they use?
  18. 1000MileStylez

    arp head studs 123-4003

    only used for fitting. never torqued. $65 shipped
  19. 1000MileStylez

    Eagle Crank key

    My timing chain key got lost somehow. It came with the eagle crank. never got a chance to measure it. The key from the stock crank is too loose. Anyone got one?
  20. 1000MileStylez

    Sealed Power Standard rod bearings

    PART # 3755APA set of 6 make offer..... i take paypal
Top