Search results

  1. M

    Need stock untouched 8445 heads

    Need a stock set that I can port on for my car.
  3. M

    2 GN wheels.

    Cleaning out the garage. Perfect for cores or widening. Wheels are not mint but they are not bent. $100 TFL
  4. M

    ATR passenger side header

    Header is used. $125 shipped. Paypal excepted.
  5. M

    Virgin 8445 Heads

    Need un-ported heads in GC.
  6. M

    67 to 70

    Give me a call if you have one with low miles and in good condition. 757-927-5232 John
  7. M

    Wrecked GN

    I need the RR tail light and trim, RR bumper filer (fiberglass), RR molding and of course the rear bumper. Call me 757-343-8675 Marc
  8. M

    ATR stock style header

    This the hot ticket if your using a stock re-welded header. Header is slightly egged but sealed fine when a removed it from the car. I really don't want to sell it but I must make room besides I know someone will need it. $125 OBO shipped. TFL Marc
  9. M

    Ported Irons

    Heads are up for sale. Have stock valves back-cut and Comp 981 springs. Driven on the street less than 500 miles. Ported by local shop. $500 OBO. I accept paypal but you must add the 4%. TFL Marc 757-343-8675
  10. M

    ATR stock style DP with cutout.

    $250. 3" with cutout. I had to cut the DP out because someone used a muffler clamp instead of a band clamp. It is cut flush. $250. I except paypal...You add the 4%. Shipping will be determined by location. TFL
  11. M

    Mustang Hybrid

    I have been following several post. I know AJE makes a tubular cross- member for a SBC. Will it work with a buick? I know a SBC will fit in a regal. I have a HB. I have seen several buick DP's mostly on the passenger side because of stock style headers. Some of the SBF have them on the drivers...
    • MIB
    • Thread
    • Replies: 6
    • Forum: HYBRIDS
  12. M

    Parts for sale.

    Precision .65 A/R housing. $75 shipped B&M cooler. $40 shipped Alluminum Drums. $70 shipped Paypal excepted...add the 4%. TFL
  13. M

    New 214/224 with GM lifters

    Valve lift INT .472 EXT .496. $125 shipped. TFL
  14. M

    87 GN Roller

    Car doe not have a motor or tranny. Car does have rust in the qtrs and doors. I have qtrs and other parts from a donor. Car is lowered in the front with drop spindles. Interior is faded but the seats are not ripped. I just don't have the time to bring her back from the dead. PM me for more...
  15. M

    BILLET 9X11 3500 stall LU

    Stall have very limited miles on it probably less than 5K. I am the original owner $500 without shipping or OBO. This convertor is heavy! TFL Marc
  16. M

    TA knock-offs.

    Selling my TA knock off headers. I purchased them last fall. I ported them to match a SCE copper gasket. I will include gaskets that came with the headers and original clamps. The turbo flange holes have been reamed to straighten out the turbo. Everything fit in my car when I did the mock-up...
  17. M

    2 Weld Prostars 15x8 3.5 bs

    I am selling these to get something a little wider. $250 w/o center caps. I just thought I would give the "locals" a shot first :D. Thanks Marc
  18. M

    Art Carr 19930-M

    What is the stall on this convertor? It is a NLU. Thanks Marc
  19. M

    Dead Injectors 4 and 6?

    I have been experiencing a misfire. I have high BLM's @160. I can bandaid it by raising my fuel pressure from @44 PSI to lower them. I have replaced all hoses. Checked the exhaust, EGR, check valves, throttle body, PCV, CCI, coils. I have sent the ECM to Bob to have it tested. It's fine. I have...
  20. M

    Billet 9X11 3500 stall

    I am selling this to move to a little more stall. This was installed in my 2003. It has less than 3K on it. I have painted it flat black but you can still tell it's billet. I am asking $550 shipped! I weighed it and it's right at 40lbs.
  21. M

    PS pump line

    I need the hard line to the top of the PS pump. Thanks Marc
Top