Search results

  1. R

    TURBO PRO BRACKET PAYING 6 SPOTS

    Congratulations to Bob Hinson on the win. Thank you to Bob, Rob, and the sponsors for making the class happen. Look forward to doing it again next year!
  2. R

    CNP best mounting locations / solutions pictures and advice needed.

    Here is a coil bracket originally for LS coils modified for FAST coils. Here are FAST coils mounted in stock location
  3. R

    THS qualified times

    Earl Stanley Jr. was car number 8062. He went a 10.583 @ 128.75 on his second pass.
  4. R

    Aem 3.5 bar map install?

    Using stock source for 5v
  5. R

    Aem 3.5 bar map install?

    I replied to your PM also. I cannot locate part number but remember there were several 3 cavity connectors available. Probably best to call Caspers.
  6. R

    Anyone tried the Borg Warner S484 turbo yet?

    I do plan to turn it up. Just taking it slow due to 93 octane and methanol as I am not sure the limit. I also may be out of intercooler (CAS V2) and hope to have data soon as I have added the hot side pressure and temp sensors to test.
  7. R

    Anyone tried the Borg Warner S484 turbo yet?

    The only 4 bolt housing I have personal experience with was the T4 .96 AR that was on the 76GTS. I was told that housing was restrictive for the 75mm exhaust wheel. I was told that if I wanted to squeeze everything out of the turbine I should go with the 1.30 Tial housing but would sacrifice...
  8. R

    Anyone tried the Borg Warner S484 turbo yet?

    Yes 9.04 was with that turbo. I was on the fence about going with the cast 76 or the 80 billet compressor and opted for the 76 cause I was afraid of spool up. Probably would have been fine with the 80.
  9. R

    Anyone tried the Borg Warner S484 turbo yet?

    The turbo is a cast wheel 76 with the race cover. After engaging transbrake and going WOT, it take 1.65 seconds to go from vacuum to 6.4 lbs of boost with the 2 step at 3600 rpm and boost controller set for 7 lb. launch. Once the wastegate starts to open about the 6.4 psi mark, the boost curve...
  10. R

    Anyone tried the Borg Warner S484 turbo yet?

    To give a better answer I pulled up a couple of xfi logs. When leaving at 3600 rpm and 7 psi boost engine would be at 27psi in 1.05 seconds. After that, I can see the boost curve flatten out as the AMS 1000 takes over and boost settles at 28 to 29. Ramp time on AMS was set to 1.1 seconds to be...
  11. R

    Anyone tried the Borg Warner S484 turbo yet?

    I had a mechanical gauge measuring back pressure last year that has a check valve so it held peak pressure. I saw 45 psi of BP when when 28 to 29 lb of boost. With the 76 GTS I was over 60 psi at the same boost. I have a pressure sensor on the car now to log with Xfi and hope to have more data...
  12. R

    Anyone tried the Borg Warner S484 turbo yet?

    It is a little slower than my 76GTS which had the 75mm turbine but not much. It is definitely street drivable with a 274" engine.
  13. R

    Anyone tried the Borg Warner S484 turbo yet?

    Here are some photos of how I installed my S476 from Work Turbo. It is a 76 cast compressor with the 87/82 turbine using the Tial 1.16 V band exhaust housing.
  14. R

    Aem 3.5 bar map install?

    You will need to make it. The AEM MAP comes with a connector and terminals that mates to it. I had to get the connector that mates to the factory MAP harness from Caspers.
  15. R

    Aem 3.5 bar map install?

    I have my AEM map installed in the stock MAP location. Got a connector from Caspers and made an adapter harness so no cutting of the factory wiring.
  16. R

    3/8" Pushrod fit in TA Aluminum heads?

    3/8" to 5/16" tapered pushrods could be an option for you. I use them currently.
  17. R

    Valve Lash Question

    I have followed the guideline in the attached link and it has worked out for me to be accurate. It calls for subtracting .006" from the hot lash setting. http://www.cranecams.com/pdf-tech-tips/mech-lift.pdf
  18. R

    Transmission cross member

    I will take it. I will PM you my address. Let me know how you want payment.
Top