Search results

a racetronix double pumper kit been on for a few years seem to have suddenly lost any fuel being pumped I have a fuel pressure gauge inside and getting nothing for pressure for fuel and can not hear pump coming on just happened suddenly what triggers the pump to come on the 2 fuses on the...

I have a pretty good draw on my battery coming off of rhe fuse that powers dome lights , electric door locks , etc I had my stero tied onto this but so far have disconnected the complete stero system , disconnected door locks ,its pulling about milla amps I think that's right the milliamps part...

hey everyone I have a odd problem seems during day with no headlights on dash is illuminated fine but once I turn on headlights the display goes almost totally dark and the dimmer does not seem to change that at all any ideas why illuminated during day but once I turn on headlights goes dim and...

hey everyone I am looking for a good set of the trunk rubber stops that are on each end of the back of the trunk I assume they act as a stop and keep the trunk from rattling thanks , john

need the plastic housing that holds the dimmer switch and headlight switch if u have a known good dimmer switch also would be great , even a good headlight switch if the writing on the switch is still in good shape thanks john

hey guys I am need of a good condiotion belt tensioner thanks john

anyone know where I can get a replacent bottle for my older smc kit it is getting brittle and worried about leaks everything else works great thanks for any help john

just getting car back on road after long engine build car sat for almost 2 years , there is this terrible creaking noise coming from the dash area seems to be on driver side sounds terrible driving down road is there something under the dash that would be creaking from sitting so long or cant...

car is running grat on cold start but after warm up idle is all over the place and idle recovery is poor noticed that my scan master shows 71 degrees on air temp no matter what can that be a prob ??

looking for a rear view mirror clean with no problems with mirror coating thanks john

need for both sides of rear door jam at bottom I think they are releases

guys question is I have a stripped upper right hand side water pump bolt , not the long one the one on yhe upper right side that goes into block can I tap it or will metal shavings end up in motor thanks for any input in advance john

looking for a new or like new throttle cable and the block off plate on the timing cover thanks jhn

hello guys , i just had a complete engine built from a local machine shop that had great rep. just did my initial start up and have driven just around neighborhood . after car reaches about 160 - 170 degress i am seeing alomst no oil pressure at idle . i have a mechanical auto meter gauge for...

hey guys just fired up this new motor , everything is new crank , rods, pistons , cam , lifters, roller rockers etc as the car warms up sitting in driveway i have about 10 pounds of oil pressure at idle . old engine held like 20 at idle . should i be worried about this im going to contact...

have my drill attached to oil pump shaft and trying to prime motor but not sure what direction to go with drill ?? thanks

hey guys i had that other post up about car not starting after rebuild " new motor no start "" i have narrowed my problem too this . i have spark , i have fuel and the gen 2 is set up correctly . i have found unless im really dumb that my problem has been no compresssion do to the...

thanks in advance for any input and suggestions . eveyone on here has always been great ! ok just finishing up install on a new stroker motor , went full roller all 4 billiet caps and rjc s girdle :) figured more safe then sorry , anyway , have everything hooked up i am running a maf gen 2 ...

i have a racetronix double pumper installed in tank , been working on car and new motor for months . lost paper to the kit so need to know which of the 3 plugs up top by firewall does the hobbs switch plug into for the secondary fuel pump ,,,,thanks in advance guys JOHN

just installed a new dual fan set up from summit , it has dual spal fans each with a 2 wire lead off each fan . i see on the factory harness there is 4 wires . so not sure what the origanal 4 wire plug was doing or how i should wire these in thanks in advance for all help and replies !!