Search results

  1. NoVA_87_GN

    Scanmaster data

    Finally got around to relocating the vapor canister and take her out in the road with the new maf translator settings and new air intake. For some reason now my blm is at 142. It was 130 with incorrect translator settings and stock air intake. Any ideas? Seems like I’m always chasing the blm...
  2. NoVA_87_GN

    Scanmaster data

    Checked out the settings in the MAF yesterday, turns out, the dip switches were set to ON ON OFF OFF, I have a TT chip, so I switched it t ON ON ON OFF, base and wot dials were set to 0, changed base to 3, wot stayed at 0. I'm installing a shorty intake tomorrow, i'll reset the ecm after that...
  3. NoVA_87_GN

    Scanmaster data

    Yes sir, set to 43 with the vac line off. When I put it back on it settles to about 36. Should I raise the line off number so that it settles to 38 with the line back on?
  4. NoVA_87_GN

    Scanmaster data

    @Dan SS2471 thanks, i'll tweak the TPS a bit to 0.42 @SCOOBY DOO thanks for the link, i'll take a look at it. I purchased the lt1 maf and translator together, product said translator was shipped programmed for lt1 maf, but i'll crack her open and verify. o2 sensor is new, put a new one in when...
  5. NoVA_87_GN

    Scanmaster data

    @~JM~ and @TexasT Thanks for the response. I'm gonna take a look at that webpage and read up on it. I've been monitoring the BLMs while driving, they are moving up and down as i accelerate/cruise/brake. The car seems to be running great, probably the best its been running since I've owned her...
  6. NoVA_87_GN

    Scanmaster data

    Update *** So I went ahead and adjusted my TPS and my IAC. I also went ahead and swapped out my MAF with an LT1 and MAF translator. Car runs good, here’s my new numbers washer getting her warmed up: Mv:236 Maf 4 Lv8 30 Volts 14 Int 128 BLM 130 Tps 0.40 Iac 23 O2 cc 118 These numbers good?
  7. NoVA_87_GN

    Misc. Engine Parts, Compressor, Turbo Cover, Etc.

    still have the cut turbo cover available? will it fit a 3" dp?
  8. NoVA_87_GN

    2x maf translators and one ls sensor 20k mile oil cap and tube

    still got the maf with sensor available?
  9. NoVA_87_GN

    Scanmaster data

    @SCOOBY DOO yeah it was warmed up, i drove it back from the shop after an alignment. I'll look into resetting the IAC and adjusting it along with the TPS. I do have a smoke machine, any ideas on where I could pump smoke into the vacuum lines to see where i might have a leak?
  10. NoVA_87_GN

    Scanmaster data

    @TexasT I'll keep an eye on the O2 and MAF numbers when I take it out next time, see if it's moving. Still have stock MAF, looking at purchasing LT1 and MAF translator shortly and installing it. @salvageV6 0.50 TPS is not a typo, that's what it's reading. I'm looking to adjust the TPS and IAC...
  11. NoVA_87_GN

    Scanmaster data

    Was hoping to get some help and see if my data is good. I’ve done quite a bit to the car, new exhaust headers, new cross over pipe, new 3” down pipe, new gn1 3” exhaust and test pipe setup, new stretched slic, new radiator and dual fan setup, new umi suspension kit and steering components. 42lbs...
  12. NoVA_87_GN

    Maf translator

    @Plains Drifter might be interested, how much you asking?
  13. NoVA_87_GN

    Smoke Test

    Wondering where can i inject smoke on the intake side of the engine to see if i have any leaks anywhere. I pumped smoke into one tailpipe (plugged the other) and saw i was leaking at my band clamps. I assumed this verified all way through the downpipe and exhaust headers, that sound about...
  14. NoVA_87_GN

    Exhaust System Leaks

    Wondering if anyone had any tips to seal up exhaust leaks? I put in the GN1 3" exhaust system and it looks awesome but when i ran a smoke test on it (plugged one tailpipe, pumped smoke into the other, every band clamp i had was leaking, especially the band clamp between the test pipe and...
  15. NoVA_87_GN

    Bleeding Front Brakes

    **Update** Thanks to the input it looks like I'm going to be able bleed all four brakes tonight. I purchased that gizmo off ebay that was mentioned. I read somewhere that if you step on the brake pedal a few times it will re-center the piston in the prop valve, which I did after i pulled the...
  16. NoVA_87_GN

    Bleeding Front Brakes

    @Anthony P thanks for the tip. I am not using that blender to gizmo, didn’t knows I needed to in order to bleed the front brakes. Don’t believe I ever read about it when I searched the threads. So I just put it in place where the light is, bleed it then pull the gizmo and out the light back on?
  17. NoVA_87_GN

    Bleeding Front Brakes

    Hoping to get some clarity. I've read through a bunch of posts, but I seem to be having an issues bleeding my front brakes. I have powermaster setup with the acc ball, I pumped the brakes 10 times to get all the brake fluid out of the ball. I bled the rear (had to replace rear cylinder assembly...
  18. NoVA_87_GN

    Anything I should replace

    I’m working my way through the car. As you can see by the pic, got a bunch of parts out while I’m cleaning stuff up. While I got access, is there anything that I should consider replacing?
  19. NoVA_87_GN

    Catback/Catalytic converter mounting tab

    thanks fellas, this looks like it'll work. this car is slowly becoming very pricey.
  20. NoVA_87_GN

    Catback/Catalytic converter mounting tab

    @OConnor thanks, I have the hanger portion off the trans Mount and the rubber, just missing the piece off the exhaust collector which bolts into the rubber straps.
Top