Search results

I’ll be painting the black on some GN wheels this week. Any simple procedure besides masking , trimming and doing a rattle can of semigloss ?

Is there a way to identify a normal rotation powersteering pump vs our reverse rotation units? I had to buy a new(Rebuilt) one but would like to confirm its correct before installing and running fluid thru it.

87 Ttype needs replacement power steering pump. Anybody have a good spare availabl?

I’m needing a replacement Altenator. I did a search but don’t see anything on the GM 140 amp Altenator. I think it was available an certain LT1 motors, but I don’t know which model cars or which years Would be a direct bolt in for the GN. Any thoughts? nobody has the replacement 120 amp units...

If I were to lose a keeper from my stock GN heads, can I use a v8-455 or 350 set of valve spring retainers? Not sure if they are the same size

Not the car in my sig. This one is mostly stock. 140,0000 miles. starts and runs well up to about 3800 rpm. then noses over like weak valvesprings. Thats one of the first things Ill look at next week, but I would expect it to rev higher than this. I attached a powerlogger file if anybody...

Im needing the Drivers side wheel trim. rear. Any out there? Northwest Indiana area

Im replacing the original dry rotted door window sweeps. The outer seem like a direct replacement. 6 or 7 screws and done. The inner are held onto the door panel with large staples that wont be reusable. Are those stock style staples available or is there a better way to attach. Glue might...

Scanmaster.......$175 staying at redroof call meat (616)304-0936

I haven't seen any vendors selling it this year. I f anybody is willing to sell a bottle please message me.

I haven't seen any vendors selling it this year. I f anybody is willing to sell a bottle please message me.

What are the symptoms of a TV cable that is too long? When I do the TV cable adjustment by pushing in the direction of the firewall then depressing the pedal, Im only getting a single click, new rebuild on the transmission, Im still getting used to the way it shifts

Here are a couple of recent data logs. I think battery voltage is somewhat low. Any other comments? first run was about 22psi and second at 24psi. Wideband selected is LC1. New O2. New razors kit. This is n street tires so there is some spin early in the run

and misc parts. I couldnt edit the title of my earlier post Powerlogger $200 Never used Cardon accumulator ball. $75 Direct scan $50. Box and Cable Permanent mount Hood mounted fuel gauge. $75 Call 616-304-0936 staying at RedRoof Inn

Powerlogger $200 Never used Cardon accumulator ball. $75 Direct scan $50. Box and Cable Permanent mount Hood mounted fuel gauge. $75 Call 616-304-0936 staying at RedRoof Inn

Just hooked up innovate LM1 Wideband. Took the car out for some 3rd gear pulls. AF at WOT about 10.9.....Good or bad? I attached a couple of PLogger screenshots Getting some occasional knock. seems to be worse in 1st and second. maybe just wheel spin

Im pulling this off and running race gas for the rest of the year. Single nozzle system with progressive controller, modified taknk for alky and the hoses and fittings. The pump shows just over 100# spray pressure when I hit the test button. I also have about 3-4 gallons of alky left that I...

Iv been looking for some knock that comes on early at about 5# boost.. I replaced the heatedO2 sensor because the cross counts seemed to update pretty slow. New Denso O2 is about the same. Looks lazy I think. Heres a few quick logs I did to show

Im getting a few drops of coolant from the motor. somewhere above the starter. Doesnt seem to be freeze plugs, no steam and cant smell it. Best I can see so far is maybe seeping from the lower rear headbolt area. If that is the case is a headgasket the only fix? How about removing the bolt and...

http://autos.yahoo.com/news/guy-building-skyline-based-aston-martin-db4-replica-193043575.ht A New Zealand native by the name of Ivan Sentch is “sculpting” his very own Aston Martin DB4 in his garage using a 3D printer, and basing it mostly off a Nissan Skyline GTS. Having only been in use...