Search results

Just got my transmission back from a rebuild. Installed, filled and noticed some leakage. Cleaned twice and found it was coming from the servo. Emailed builder but it's the weekend and I'm impatient and I've got the next few weekends booked. Can't find any how-to's to remove the cover. I'd...

See attached pic. I have the relays tied together and it's been this way since I've owned it and never messed with it because it works. I'm going to be installing a dual fan set-up from alradco and I want to know why the green wire is tied into the green with white tracer wire? I've seen ways...

I finally got to the track last night and I noticed something strange. I'm getting a spike of 19+ just after launch (between 20-35 mph). This happened on all 3 runs. After the spike, it drops to around 10 and then rises slowly to a my set point of 11. I'm not sure what is going on. I have...

So far, saddle bracket bolts weren't long enough. Asked for new ones and took over a week to get them. Yes, it's easier to buy them and that's what I ended up doing. Bolted the brackets up and the brackets are just a bit too big so they spin on the axle housing. I have to take off material...

Is there an adapter plate to go to the 3"dump to 4" single shot or is there a dump/testpipe that works? I rather go with an adapter so I don't have to weld in another O2 bung.

I'm trying to identify if I have the RJC or GN1 single shot. The muffler has no identifying marks on it. Any way of telling??

I'm looking for a working control head. I already have two non-working ones so I don't need another. Let me know what you got and a price. Thanks, Sean

Finally installed the last piece of my build (balancer) and the reluctor ring is rubbing the front cover. Anybody else had this problem? No thrust play. Stocker didn't rub. Proper clearance on sensor. I've got enough room to get a small grinding bit to get the clearance needed. Anybody...

Long story short, one of the pins on panel is pushed in and I can't get my fat fingers behind the panel to push it back. No luck on trying to hook it through. Bulkhead connector is easy to get off in the engine bay but looking at it from the inside, I only see a couple bolts holding it in...

What is the axle tube diameter for a stock TB? 2 5/8" or 3"? Thanks, Sean

Sold it a few years ago to my brother and I'm getting her back! GN is too fast now and I decided to stop putting goodies on it. I don't have the heart to cage it so I'm going to actually make the T a full race car. Decisions, decisions.... Posted from the TurboBuick.Com mobile app

PL only connects with key on and won't connect when running. Tried XP and Win8 to no avail. I get a 'cannot open port' error. Posted from the TurboBuick.Com mobile app

Long story short, been chasing down a problem since June and Eric and Bob have been nothing but help. From countless e-mails to one-on-one support on the phone, they've been there for me. I know these guys have lots of things going on and just to know that they take the time out to answer even...

I'm hoping the title got your attention. I've been trying to figure this out this whole summer. Been in talks with Eric Marshall and Bob Bailey and still can't figure it out. I'm going to open it up to you guys to see if I can get some more ideas and hopefully a fix action. When this first...

I'm looking for the location of ECM grounds: pins A12, D10, D6, and D1. Any help would be appreciated!

Been trying to figure out a problem for a while. Long story short, changed wires, coil pack/module with known good ones, ecm, maf, checked grounds and power cables, etc... Noticed this when the car started breaking up real bad now when cruising, car will just flat out die. Fuel pressure is...

There is an insert for the line that goes from the motor to the master cylinder body. Where the line goes into the body, the insert is missing. Found this out when I changed the unit out and it sprayed fluid everywhere. No idea where it went. I have another unit with the insert but doesn't...

5th time doing it and can't get it right. I understand which one I'm supposed to adjust but I think I'm not adjusting them right. Here's what I'm doing: half turn after zero lash. I'm doing this cold, intake on. I have Scorpion rollers and Morel roller lifters on GN1's. Pushrod length is...

Did a search and found very little. I feel that this way is easier. (tried both) My question is am I doing it right. (GN1's, Scorpion rollers, Morel rollers) I get it to operating temperature, pull the valve cover off, loosen the locking nut, loosen the adjusting nut until it starts...

I have the AVC dash and I am troubleshooting why my gauge is pegged. I've got continuity from the sending unit case to the a known good ground so I'm good there. Does anybody know the voltage of the sending wire? I think it's the sending unit but I just want to make sure. TIA,