Search results

  1. T

    Servo leaking (new rebuild)

    Got the cover off but the o-ring was not sealed properly. The builder had it off a few times trying to adjust the pin length and overlooked it. Honest mistake and took all blame for it. He's over nighting a new o-ring just to be on the safe side. BTW, the snap ring was a bit of a pain to get...
  2. T

    Servo leaking (new rebuild)

    That was very, very detailed and I'll definately use this as my guid for sure. Hopefully the builder will get back to me in the morning. Thanks for all the replies.
  3. T

    Servo leaking (new rebuild)

    I'll practice on my spare transmission. Easier to see what I'll be up against when I do the one in my car.
  4. T

    Servo leaking (new rebuild)

    Just got my transmission back from a rebuild. Installed, filled and noticed some leakage. Cleaned twice and found it was coming from the servo. Emailed builder but it's the weekend and I'm impatient and I've got the next few weekends booked. Can't find any how-to's to remove the cover. I'd...
  5. T

    1986 T-Type- $15

    I know some were missing from the factory. I didn't know if you may have put new ones in during the paint job. No worries. Thanks!!
  6. T

    1986 T-Type- $15

    Are all the body bushings in place? Also, you say 'These cars have to go' so I'm assuming you have more than one for sale? If it's another TB, can you share? I may have missed it above. I may have two folks interested in it. It's a very nice car. TIA, Sean
  7. T

    1986 T-Type- $15

    How far from St. Louis are you?
  8. T

    low and high speed relays ties together, pic attached

    Installed the dual fan kit from Alradco. I went ahead an left it jumpered and the fans worked as advertised. One fan kicks on then a few seconds later the second one kicked on. I'm leaving it and calling it good.
  9. T

    low and high speed relays ties together, pic attached

    That's what I thought but wanted to make sure. Do you happen to know if the dual fan set-up will work the same or should I undo the tap?
  10. T

    low and high speed relays ties together, pic attached

    See attached pic. I have the relays tied together and it's been this way since I've owned it and never messed with it because it works. I'm going to be installing a dual fan set-up from alradco and I want to know why the green wire is tied into the green with white tracer wire? I've seen ways...
  11. T

    WB spike of 19+ after launch (6.1 TT alky chip)

    Found my problem. I guess when I changed the O2, I pulled the wiring and it laid onto the dp. Not sure why it only causes the spike after the launch. I'll splice it and report back after a couple test hits.
  12. T

    WB spike of 19+ after launch (6.1 TT alky chip)

    I finally got to the track last night and I noticed something strange. I'm getting a spike of 19+ just after launch (between 20-35 mph). This happened on all 3 runs. After the spike, it drops to around 10 and then rises slowly to a my set point of 11. I'm not sure what is going on. I have...
  13. T

    Axle tube diameter

    Did you get the correct one?
  14. T

    Axle tube diameter

    Just measured mine. 2.75" on the dot...well almost.
  15. T

    Axle tube diameter

    Mine are 2.75". If you measured yours and they are 2.75" than I would bet you that's what they are.
  16. T

    BMR Xtreme Anti Roll Bar install problems

    So far, saddle bracket bolts weren't long enough. Asked for new ones and took over a week to get them. Yes, it's easier to buy them and that's what I ended up doing. Bolted the brackets up and the brackets are just a bit too big so they spin on the axle housing. I have to take off material...
  17. T

    4"single shot adapter plate

    Willing to send me material is awesome! You don't have to do anything like that but man, I appreciate it! Above and beyond! I'm going to school lounge around my father in laws place for something more suitable. I've got babies now and I don't want to have toxic fumes in the car. Reason why...
  18. T

    4"single shot adapter plate

    I was just using what I had laying around. I figured it would be better to use because of rust. I had no idea about the fumes associated with high heat and aluminum.
  19. T

    4"single shot adapter plate

    I'm surprised too. I got a hold of some of some 3/8" aluminium plate and I'm going to make one. It'll be cheaper to do that and I won't have to weld in another bung for my wideband since I'll still be using my current dump pipe.
Top