Search results

Looking for an old school front mount preferably an ESP. Pipes need to be included. Going a different direction for my build & not looking to go RJC for my preference. Let me know what ya got. Thanks.

Just a heads up, beware of PickerSandra she slid into my DM’s this morning & not in a sexy way!!! I have reported him/her/she/they/them/us.

Putting some feelers out there to see what’s available for a stretched SLIC. Let me know.

Hey everyone. I’ve searched & read the belt length threads, however is anyone using a 1600(just a CH under 63”) belt? I had a 1620(63.7) & my tensioner was at the upper limits. I went to a 1615(63.5) & it started ok, then once it stretched is close to the upper limit on the tensioner again. So...

Looking for the panel for under the DS dash. Good condition please. Let me know what ya got. Thanks!

Hey everyone, going roller on my new build & getting rid of some of my current stuff. Stock IC fan $75 shipped. RJC shaft supports(x4) $60 shipped TA thicker shaft rocker assembly. buttons, rockers, & shafts with less than 1,500 miles on them. $200 shipped.

Hey Guys. Anyone know what this relay is for in the Pass. side kick panel? Was putting sound deadener in & this relay is behind the ECU. Just for future reference in case it ever needs to be replaced. Thanks!

What are your opinions on leaving the stock fuel lines? Going to E85 & have -6 & -8 Teflon lines. Do I keep the stock fuel lines in JIC for the future or take them out? I know once you put the -6 & -8 no one really goes back to stock.

Is there a way to refresh the stock timing tab? It's a yellow tinged plastic now. Paint possibly? I see TA sells one. Theirs seems to be a powder coated metal though. Though I'd prefer to refresh it myself. Thanks.

Selling my set of metal vacuum lines. Good shape. Needs a clean & possibly a fresh coat of paint. SOLD!! Also have a billet vacuum block w/gasket. Has port for vacuum brakes. $30 shipped.

Looking for a set of roller rockers for my new build. Open to 1.55 or 1.6. Let me know what’s out there before I go to Harland or T&D. Thanks.

Sorry for another ECU post. When do guys start going to an aftermarket ECU? I've got a new motor build coming, going to E85, have SM, & PL installed. I just read the most recent post saying they're not really needed. I'd like opinions as I like the deeper tuning possibilities, safety features...

Selling my stock ECM(pins cleaned off for Powerlogger). Upgrading to bigger injectors & modded ECM. Also includes 60# Deka injectors with matching ALKY 6.1 wideband chip from Eric at TT. $325 plus the ride.

Razor single nozzle ALKY kit. Comes with everything you see. New on/off/test control from Don. 3” RJC uppipe with hole already drilled. Pump from 2021(recommended sending it to Don for a rebuild. You’ll need a 3bar MAP & bulbs.

Hey guys I know this has been done a handful of times, winter is here, & I want to get rid of the vacuum lines & block. Does anyone remember the drill & tap sizes for the vacuum lines & the for vacuum brakes? Thanks

Hey guys. Anyone out there reproing or have a set(2) of 15x8 Vector rims? Looking to go from a 255 in the rear to 275. Thanks

Hey guys, replacing the headliner & upper door panels soon & I want to remove the old tar deadener with newer stuff. How many sq. ft(roughly) would be needed to do the roof, doors(inner & outer), & floors? Won't be going crazy. Not doing trunk quarters etc. Thanks!

Hey guys. Troubleshooting my A/C not coming through the vents. I'm aware it could be an actuator as well as a stuck door. I have about 13" of vacuum on the line at the fender vacuum ball & 13" where the violet hose connects to the vacuum control switch. However when I switch to NORM, BI-LEVEL...

Hey everyone. Have some parts for sale as I've made some changes. Prices listed buyer pays for shipping. Thanks fo lookin'! 1.) Stock set of valve covers. Will need the filter/gasket for the pass side. $50. 2.) TT 5.7 alcohol chip for 60# injectors. $40 3.) Oil fill cap & tube. Tube has a...

Hey everyone, Have the doors apart for window adjustment & I see my rollers are flat spotted. What is everyone using for the rollers? I saw the GBody parts set but that's almost $60 for six rollers(yeah, yeah I know Buick's ain't cheap). Is there a Dorman or a Help brand that people use with...