Search results

  1. G

    85 T Type rebuild

    How much were they going for when they first came out?
  2. G

    4.1 Stroker Build

    Hi does anyone know what the led bulb conversion numbers are to replace the stock ones inside the stock radio? I have the concert sound 5 band eq radio. Thanks
  3. G

    New boost Gauge question

    Good to hear thanks! Getting my car ready after a 15 year sleep. she is starting to wake up! Alky kit next.
  4. G

    New boost Gauge question

    When the car is not running it is a zero. when the car is running at idle it's around 20 hg. My old vdo gauge did not have vacuum boost only. Correction I miss read the gauge. its at 16hg idle. thank you
  5. G

    New boost Gauge question

    Hi I installed a new vdo 30hg 25 boost gauge and when the car is at idle the gauge is at 20hg. When the car is off it's at 0. Is this normal? Thanks
  6. G

    Low boost issue

    Wow good ideas here. I'll try that. then I'll look into what Bison posted. Thanks for the replies!
  7. G

    Low boost issue

    Thanks Dank, I removed the boost controller and I see a pin hole on the 90 degree elbow. I took the rjc apart but I do not see a flap. just a steel ball and spring came out. I was able to push air through the elbow and I felt air coming from the pin hole. Anyways I kept the rjc off and connected...
  8. G

    Low boost issue

    Hi I did a search on this and could not get a clear answer. No matter how tight I have the actuator rod and the RJC boost controller all the way screwed down I can only get 14-15 lbs of boost. The car sat for 15 years after I rebuilt it but I never got on it since then. Scanmaster readings are...
  9. G

    Aftermarket turbo gauge question

    Thank you! That makes sense it tees in with the map sensor vac line.
  10. G

    Aftermarket turbo gauge question

    Where is the best place to splice the vacuum line for aftermarket turbo gauge? Thank you
  11. G

    Need help to remove cam gear

    Never mind guys got with flywheel puller. thnx
  12. G

    Need help to remove cam gear

    I removed the cam bolt /button off my rollmaster double roller gear set but the cam gear wont budge. I'm about to put a fly wheel puller around the distributor gear to pull it. Any suggestions? Thanks
  13. G

    Please help with timing gear set

    I went to the rollmaster website and almost all gear sets are just like the diagram that RmvBfrFlght posted. Looks like I'm 6 degrees advanced. Can It still run good like that? I still havnt put much boost through it yet.
  14. G

    Please help with timing gear set

    Yes! That diagram looks familiar that Weber sent me years ago. I left him a message to get back with me. the 2 dots make sense now. one for the key slot and the other to line up both dots on cam gear and crank gear. The slot for the 2A on your diagram is different than mine though. Mine's a...
  15. G

    Please help with timing gear set

    I thought it might be backwards too but the dots are facing me. If the cam gear dot is pointing straight down would that put number 1 piston at TDC?
  16. G

    Please help with timing gear set

    Hey guys I just got my GN out of storage after 15 years. Ive been out of the loop for a long time and want to get my car going again. Anyways my front main seal rotted out and leaking oil so I took the front cover off and decided to check the 2 dots that line up the cam and crank shaft. its a...
  17. G

    Headlight chime module Wiring help

    Hi Vader where did you buy yours? I've looked all over the internet and cannot find a chime module for the GN.
  18. G

    Alternator volts

    I had the same issue and drove me nuts. Long story short, it turned out that it was the copper terminals in my dash that plugs in like an old atari cartridge. The brown wire that leads from the alterantor into the dash had a bad connection in the dash which was causing my alternator to appear...
  19. G

    Dang electical problems!

    I'm pretty sure it's your power antenna making that noise and it's broke not able to be fully up or down. You can unplug it from under the hood. Just follow the wire that leads to the antenna you should see a plug to take it apart. You can leave it like that until you fix your antenna. I left...
  20. G

    Walbro 307 and 40# Red stripes ?

    Hi all I've been out of the loop from Turbobuick.com for some years now and trying to get updated. I have a walbro 307 in my tank and 40# redstripes installed a long time ago. Is that enough fuel to support mid elevens or should I update to walbro 340 and 60lb injectors like I see many of you...
Top