Search results

  1. E

    Power seats vs non power seats

    Is there and difference in the seat? Can you swap a non power seat on to a power seat base/track?
  2. E

    Stock 86-87 oil pan

    Anyone got a spare?
  3. E

    Rattle in Park

    Anyone ever experience a rattle like sound while in Park like a loud rattling converter shield but doesn't make the noise in reverse, neural or drive? While idling in Park, the noise gets louder with tighter TV and goes away with a fully loosened TV cable adjustment. Drives fine. Happens in...
  4. E

    BMS or Billet 3.40 stroke crankshaft

    No chinese. What's out there?
  5. E

    Autolite AR3933 plugs

    Anyone have any electrical gremlins using Autolite AR3933 plugs? I believe this is a non resistor type plug. I bought a set after reading quite a few using them but then I realized they were non resistor type.
  6. E

    Coil Module Plate

    Plate that the module bolts to. Anyone got one they want to sell? Ed
  7. E

    A-Pillar Metal Trim - Exterior

    Need the long metal trim piece that runs along the a-pillar on the outside. Drivers side and black.
  8. E

    TH400 that shifts automatically

    Might have just messed up another 2004R and I'm considering the TH400 route. Is there a way to put it in drive and race it or is everyone else shifting it manually?
  9. E

    Restrictor in vacuum line "Y"

    What is the purpose of this restrictor?
  10. E

    A-Pillar molding plastic drivers side

    Looking for good condition stock piece. Color needs to be factory grey for a GN. Can trade for a dual gauge pod unit.
  11. E

    Removing 3rd and 4th gear switches

    Why would a trans builder do this in a 2004R? Interfere with a transbrake? Connector is there where you plug in the harness but there are no wires connected to the plug on the inside. Can it be added back?
  12. E

    Running a LU converter in a non LU trans

    I hear it is bad to run a non-LU convertor in a LU trans but what about the other way around? Other than the lack of efficiency, it is ok to do?
  13. E

    Non Lockup Torque Converter

    Looking for a non lockup converter. Would prefer one on the tighter side since the car has stock heads and cam with the standard bolt ons. We've got 2 separate 9/11 units for possible trade. One is billet, one is not. Ed
  14. E

    Turbo cover / shield with bolts

    I just need the turbo cover/shield and the bolts to attach to the bracket. Already have the turbo bracket. Already cut for an aftermarket DP is ok.
  15. E

    Bottom pickup filter?

    Is this a 7004R filter? Or are we still over filling a quart like we did in he old days to prevent sucking air?
  16. E

    RJC 5" Downpipe

    Anyone running one? If so, what headers? Any fitment issues?
  17. E

    Turbo exhaust housing outlet diameters

    Anyone have a 6768 or basically a turbo with a 68 exhaust wheel that can measure the exhaust housing outlet diameter? I got an external gate 3.5" DP here and the hole is only 64mm. I'm wondering if the hole is too small. The wastegate hole is 32mm.
  18. E

    Turbonetic Boost Controller

    Anyone have success using this on a stock wastegate setup?
  19. E

    THDP and Q-trim or PTE 68mm exhaust wheels

    Can the 3" THDP's puck control the boost?
  20. E

    Bias ply tire growth

    Last time out, I didn't take into account for tire growth. Lowered my RPM's going through the traps. Does anyone know how much more a slick or bias ply ET Street grows on the top end? Was using a 27" ET Street at the time. Considering 295/55/15 (27.8").
Top