Search results

I am in need of the black 27 tooth speedometer driven gear. The one that the Speedo cable slides into on the transmission. Mine is worn and my needle was erratic. I was able to find a 31 tooth white gear to use temporarily, but the speedo appears to read about 5 mph low at 50mph. Please reply...

Hello All, I have been trying to trace down a no spark, no injector pulse issue. I have traced it down to the fact that with the key on, I am not getting a voltage to either the crank sensor or the cam sensor. I do have battery voltage at pin M and P of the ignition module.connector. Where...

I set up my oil pump to tight and siezed it. :frown: It sheared the pin on the cam sensor gear, Where can I get another hardened roll pin for it? Thanks, Lorenzo

Sart at 2:20 to miss annoying music, 2:28 is where the impact is. Watch it from there to the end. F-16 vs. Tree | Military.com :eek: It's amazing he survived!!!!!! I would hate to be in his shoes when he has to explain his actions. I picture that scene from Top Gun where Maverick and Goose...

Behold the greatest Hot Wheels track in human history - From the Marbles - NASCAR*Blog - Yahoo! Sports That is just awesome, It's kinda long, but he did it for charity. I especially like the hot tub jump around 2:30 ish:) I cannot wait till my son is old enough to get into hot wheels tracks.:D

Plasma Bursts Could Replace Sparks In Car Engines | Fox News A little plasma power for the GN:biggrin:

Chevy Billboards in Detroit, Michigan I think they are pretty cool.

I just failed due to high HC. My DP to cat connection was loose so I had a major leak there during the test. Found this out when I pulled the cat to make sure the element inside wasn't cracked or damaged. Once I loosened the four bolts at rear of the cat, I could just pull the cat off the DP...

Haven't checked out Carsinbarns.com for awhile and look at the tragedy I found.:eek: CarsinBarns.com bottom of the page, called "Grand Mess" You can see someone attempted to do some bodywork on it at one time in its life, but I hate to see an Turbobuick end up in such a state. Look at the...

Good Morning, I need my drivers seat rebuilt. I have the foam and the PUI covers. CAn anyone recommend a shop that is good and fairly priced. I am located in Oceanside, CA about 40miles north of San Diego. Thanks, Lorenzo

GM Page 70 Third pic down. $750 for an 86 GN with a Bad wire.:eek: Talk about a steal. That Bill guy was in the right spot at the right time.:biggrin:

Just taking a break from layong a laminate floor and flipping thru the channels when I see a GN. Its on the episode called "Murder on the Mind". Kinda funny, It would have to be a criminal driving the GN.:rolleyes: Oh well, Back to laying the floor. Lorenzo

I got sent this and it had me LMAO:D I need to sign my wife up for class 9 ASAP!!!:eek::D She has mastered class 12 already:biggrin: Enjoy Men Teaching Classes for Women at THE ADULT LEARNING CENTER REGISTRATION MUST BE COMPLETED BY TUESDAY, MAY 3 , 2011 NOTE: DUE TO THE...

Hello everyone, I need advise on how to clean my garage floor of oil and a little bit of grease? I just spent the last few weekends trying to stop the GN from leaking oil. I think I got almost all of the major ones taken care. My problem is now my garage floor is looking pretty bad.:o I'd like...

Any HVAC guys? I have 4 quotes to replace furnace. They are all within $700. here are the 3 Furnaces they recommended (two recommended the same): York TG8s Trane XB80 Amana AH8 House is 2 story, 1400 sq ft, In southern Cali., So we only use it 3 maybe 4 months out of the year. When we...

Good Afternoon, I am looking for the above. Do you have any and how much shipped to me at my work address? Isis Pharmaceuticals Attn: Lorenzo Hernandez 1896 Rutherford Road Carlsbad, CA 92008 Thanks, Lorenzo Respond to this thread or PM me:biggrin:

I need one of the above for my ta-49 turbo. It's the metal piece and bolts you have to loosen on the inlet side of the turbo if you need to clock the housing. item number 12 and 13 on the below link (if it works:eek:) second post on this link, with the exploded diagram of a turbo. Google...

What do I need to do to have the stress cracked repaired above the top rear corners of the door windows? Anything I should tell the welder to do or watch out for? Would installing the rear set braces keep them from coming back? Getting ready to get the GN dent free and repainted, but need to...

In a scissorlift!!!!!!!!!!!:eek: YouTube - Steve's Drunk and High DUI at Work (Arrested on Scissor Lift) But he knows his rights:rolleyes: What a total idiot.

Hello, Is the stock vacuum line with the restrictor used with the MBV, or is it replaced with just vacuum lines? TIA:D