Search results

  1. A

    214-214 cam

    Hi It semes that the 214-214 cam is hard to get, What is the rpm range numbers for that cam? Does someone now where to get one?p
  2. A

    Faster 1/8 time advice

    Hi Ineed some advice to get faster 1/8 times and 60 foot. must be running 10.5x26 slicks class should i go with higher gears ? Launch boost? Start in second gear? Car weigths 3600lb What combo do you have to run mid to low 6 sec? My best et 1/4 10.27 but i am only going to race 1/8 in the future.
  3. A

    Cam advice

    Hi Ok what tire size did you have and what was your transbrake set up st launch? I have never came under 1.67 60 foot. What was your rwhp. and at what boost? How high do you rev it? Anders
  4. A

    Cam advice

    4340 steel forgeed and girdle
  5. A

    Cam advice

    I used to have a 212/212 in my old 3,8 engine and i liked it and the different in peak power isnt that big
  6. A

    Cam advice

    About 6500
  7. A

    Cam advice

    Hi! I am running the 224/224 cam today but thinking of install the 218/212 cam to get some power earlier and spare the engine from high rev all the time. Engine is going out anyway for piston rings change. What do you think of that? Anders
  8. A

    Engine type?

    Ok thanks How much can it be Worth, its a non drilled block.
  9. A

    Engine type?

    Hi! Does any one now what type of block this is and can it be used with buick heads/parts? Anders
  10. A

    need a 9.5 PTC

    For a TH400
  11. A

    need a 9.5 PTC

    Hi can someone help me were i can find a PTC 9.5 race converter about 3800 stall
  12. A

    Loss of power

    Hi! Today i had the TTA on dyno and it dont like to make any moore power even with extra boost, same hp from 21 to 26 psi. Se the attached file. I dont like this camshaft 224/224 i am current running, my old 212/212 was more fun at lower rpms, i am going to swap in a 212/218 soon and hope that...
  13. A

    Camsensor

    Hi! Is there any replacement for the stock camsensor ?
  14. A

    Still weak

    Yes it looks like it,vill try to rev it to about 6700 after i check the seatpressure an go from there
  15. A

    Still weak

    Hi! I have taken the car to the strip now and i still at the same power the old 212/212 cam/3,8 engine 67 pte 24psi made. What can be wrong, I just rev it to 5800 but now I saw people running over 7000rpm with a 4,1 stroker engine, what range does your 224/224 cam have? I am running at 26-28 psi...
  16. A

    Sump the tank

    I have never seen that, homemade ?
  17. A

    Sump the tank

    Ok, were did you go into the tank with the -8 returnline?
  18. A

    Sump the tank

    Ok but i guess i will be fine by using the old feed line as returnline?
  19. A

    Sump the tank

    Ok did you run the return fuel in the old feedline and just plug the old returnline? What type of pre and postfilter did you use?
  20. A

    Sump the tank

    Hi! I am going to sump my tank and wounder were the best place to install the external fuelpump and fuelfilter are. And i am going to use the old feedline to a returnline,do i need to do anything to it exept unstall the intank puelpump and fuelfilter ? Thanks for any pictures of your installs.
Top