Search results

I am looking for the small spoiler pieces on the fender extensions.

I have pulled all the trim off my car and wanted to know if that is body filler or hard seem sealer in the drip rail.

Should i spray soming on the back side of the quarters while i have my car tore down this far? Would it be worth while or waste of time? I have the seat belt assembly out as i am filling in the rivit holes for the side trim. Brandon

Is the guy i ran into at the track in Spokane on here? Older gentlemen with a pretty nice car.

I know there are a lot of crazy smart engine builders on this forum. What are some books one building enginges and all the tech behind different combinations of parts? I would love to go to a school like SAM but can afford it, but still want to gain the knowledge of it on my own.

I am looking for suggestions on this one. I have a bare frame that I am working on. I have rewelded 90% of the factory welds. I have some 1/4" plate to do a notch because I am there but not sure I will go through with it. I am starting to second guess doing the notch and the bracing over the...

The chassis I have had the stock fuel lines on it. When the motor was pulled the lines were crimped/cut where they go through the frent cross member. Could I just attach a braided hoses on the ends at that location or would it be wise to just go head and run all new braided lines? My car has...

Does anybody offer a new under dash harness for our cars?

I will be rebuilding my front end in the next few months. I have a few questions about parts and whats worth it. I might autocross at some point but right now my plan is just for a good driver. So I have priced out the Moog Parts for the Local Parts house. If is can spend a little more and get...

This summer I will have the motor and tranny out of my car because I am pulling the body for body work. While the motor is out I want to put new seals on the oil pan valve covers and intak. Check the timming chain and cam. I am thinking about pulling the rods and main caps to check the...

Would it be wise to paint everything at the same time opposed to painting say the fenders then a few weeks/months later painting the doors trunk ect..... Or paint the jams firewall ect put car together them do a total spray all at once?

I need some guidance on this one. My GN is a t top car hand has rust in the header under the t tops. It has rust in both quarter panels, both inner and outer rocker panels. I have priced all the sheet metal form Gbody parts. For just a little more money I can buy a rust free hard top body with...

I am looking for a known good MAF Sensor.

I picked up the stock location stretched intercooler and I am trying to find out info on it. The guy I got it from said it was a "stealth" intercooler. Can any body name it?

First I want to thank everyone who has helped me with some of my stupid questions. Now on to my A/C question. My car losses it's freon charge over a week or so. I finely ponied up and bought a dye leak kit. Simple deal. Glass with a small led black light. Shoot some dye in and go drive. I...

I bought the 1320 electronics Bluetooth scanner. I noticed that the to voltage is a little low and the iac is a little high. The car was not up to temp and the blm were high. Should I start with the top voltage and iac or start with lowering the blm? The car has a turbo tweak chip in it...

I was working on my gn today picked everything up closed the hood and went inside. Come out to go somewhere and the header panel is cracked. What the best way to fix it?

I have an 87 gn and the break pedal is low. The car was converted to vacuum breaks before I bought it. The rear breaks have s10 wheel cylinders with factory regal shoes. There is slight drag on the drums. I changed the front pads and rotors today because I had a wrapped rotor. I put EBC...

I hope in the next month or two to start the tear down on my GN for Paint. If I sand down to bear metal and want to use a sealer primer on the first layer of each panel. Could I use an aresol can primer or should I go head and use a spray gun? This will be a long process for me. I am looking at...

What does the body shell weigh? At some point I am going to start the body work on my 87 GN and I am trying to decide if I want to go head and pull the body off the frame. I will already have the doors pulled to replace them and the body mounts are shot and need replacing. What a few more...