Search results

  1. P

    ECM prom cover and screws needed

    So why does the reman ecm have a metal plate just under the one screw hole? I know both screws for the cover should be the same length but on the one side there is a bar or metal tab that is keeping the screw from going in. On the junk computer I got from the wrecking yard both are the same...
  2. P

    ECM prom cover and screws needed

    Yea maybe I'm being too anal about it. I won't worry about now and if I come across one fine, if not so be it. Thanks
  3. P

    ECM prom cover and screws needed

    Thanks but I prefer the OEM cover.
  4. P

    86-87 ECM prom cover and both screws needed

    I have a replacement ECM but they did not include the eprom cover and the 2 screws with it. Does anyone have the small cover and screws to close it up? Thanks
  5. P

    ECM prom cover and screws needed

    So I ordered a reman ECM from rockauto and received it without the metal cover and two screws. I'm not sure why they wouldn't keep it with the casing but I have to find one and the screws. The core I got from someone doesn't have it either and I don't have the original ECM. Are these available...
  6. P

    Winter storage for alky system???

    Just wanted to see what you guys do for the preparation for winter storage on the alcohol system. In the past I have run water thru the pump and nozzle and let it go at that but didn't know if that was ok or should I do more? Thanks
  7. P

    Thermostat housing leaks.... what to do??

    I didn't want someone to be confused of my signature showing an 86. I do have another hot air motor I am working on. Thanks
  8. P

    Thermostat housing leaks.... what to do??

    sorry this is on my 85 hot air motor
  9. P

    Thermostat housing leaks.... what to do??

    I am having trouble getting the housing to seal against the manifold. I have tried 2x with new gaskets and it still leaks. The housing has been cleaned but has allot of rust pits. What are you guys doing to remedy this? Can I buy or new one or try to find a good used one? Thanks
  10. P

    ENGINE BLOCK FREEZE PLUGS

    Can someone advise what the proper plug size I need for the four block freeze plugs are? I want to use brass since I just noticed one of the steel plugs has a hole in it. I see there are different cup heights used looking at the advance auto website. I am going to replace all four on the block...
  11. P

    HOOD CLOSER SHOCKS

    Can you advise what the exact length should be? I would like to measure these to check that out. Thanks
  12. P

    HOOD CLOSER SHOCKS

    Can someone show me a picture of which way the closer shocks mount? I don't know if I have them the correct way. The hood seems to be binding right before it closes and I don't know if its the shocks or something else in the alignment. Or is it usually very tight to close. Thanks paul
  13. P

    4 AN hose needed for external fuel gage

    Thanks n2buick. I am not a big fan of SS braided hose. I'm still looking for the soft braid sheath. Thanks again for the offer.
  14. P

    4 AN hose needed for external fuel gage

    Hi guys, I am trying to find some 1/4" soft braided hose for my fuel gage. It needs to be the type for push loc or socketless fittings. I don't want the rubber stuff bc over type it cracks on the outer shell and makes me nervous. That is why I want some braided weave but not SS. I can't seem to...
  15. P

    Belt tensioner bearing issue

    Thanks guys for all your replies. After removing belt found out its the front alternator brg and not the tensioner brg. Does anyone know the P/N for the front alt brg? Is it the same as the rear? Is this easily replaced? Thanks for the help.
  16. P

    Belt tensioner bearing issue

    Then I would have to press the brg out and press the new one in? Is that a simple job? Thanks
  17. P

    Belt tensioner bearing issue

    I have a stock 86 and the belt tensioner is squeaky. It drives me crazy. Last I new the tensioner pulley is discontinued. Is this true? What are others doing to fix this problem? Thanks
  18. P

    ANYONE USING THE OLD ACCEL DFI GEN 6 SYSTEM

    I need help from anyone still using this dfi system. Thanks
  19. P

    Wiring experts needed for a specific terminal connection ???

    Thanks salvagev6 but do you know what it does in the ecm? I'm trying to figure out if I need that in my ancient accel dfi system. I don't know if it ever was there or its not needed by the dfi control. Thanks for the help. paul
Top