My translator has always worked fine and when I start the car everything powers up but the translator won't change value it just shows battery voltage and rpm as it would but that's all
Hi I am installing a arms with tall ball joints with coilovers on a regal chassis. I am trying to lower the front but the camber is way too positive I have stock spindles and the lower ball joints that came on the lower arms are short. what would bee the best way to make things correct and...
I have a te-60 with an exhaust housing provision for the race gate. My question is can still I use my thdp I am using now and just get a separate exhaust dump for the racegate? I can't find much on exhaust dumps for the racegate anyone know where to get one?
thanks, George
My car starts idols and it shows millivolts and once I put it in gear and give it any sort of load all the millivolt go to zero on the scale master gauge I've tried checking the ECM and the power logger block for the ScanMaster and o2 sensor link to because I did have a code 42 for a little bit...
I have a Gn1 3" downpipe no wastegate provision I bought from someone one the forum I didn't use it because a thdp came up right after I payed for this one I I didn't even know It had no wastegate provision its a nice dp just not for my application i'll do 250 shipped and i'll get pics of it as...
Hi I am just wondering if there is a thread or source for hooking up my alky into my hot air engine? I already installed it and am using it with my 87 engine currently but will be removing it and putting the hot air engine back in the car I just was wondering as far as the nozzle hookup and any...
hi I am going to use my hot air setup again in my car and am looking for some stuff...the stuff I need is an exaust housing ,the bolts broke in it or a te33 , stainless uppipe, ported hotair intake thanks
I just recently installed an aem wideband gauge and connected the white wire to the powerlogger block... started and stalled my question is do I need powerlogger attached to use the 6.1 chip or can I run with out the plc and laptop hooked uphalf the time or is it possible a setting I messed up...
I have an 85 t type I transplanted an 87engine in the car with the ecu and harness and kept the hot air motor and everything
my question is I would like to put the hot air engine back in for while I do some work to the87 engine ..will I have to change the harness or can I keep using the 87...
Hello I have had no luck with the Z 06 screen most card style maf sensor that I have it is a screenless 4 inch pipe when I install it on the car and I set my gen 2 to 4 inch Mega Maf input the car does not start I mean it starts then stalls right away is there any settings or Target information...
I'm putting a three inch downpipe with an exhaust elbow and I'm wondering what should the torque specs be for the turbo housing to the 3 inch downpipe I'm using a copper gasket thank you
Posted from the TurboBuick.Com mobile app
I just installed the alcohol set up and I used the harness that goes from the new 3 bar map sensor to the TPS sensor and I ran the green wire from that under the dash to PaC 6 wire harness since I hoped that up I do not get boost or map pressure on my ScanMaster what do I tap or connect into so...
I'm replacing my rear control arms with box control arms when I tighten them to the Frame one of them is not snug in the pocket after I tighten the bushings location it isn't sloppy but the sleeve that goes through the bushing moves more freely than the other anyone think this might be a...
Hi I have the gen 2 translator hooked up and running with a 3"lt1 maf my question is I have a 4"maf sensor/maf pipe all in one that I want to use but when I tried configuring it it would not start .I tried maf input 4" mega maf and output gm stock (I think this is correct )the sensor is a card...
Hi I have a zo6 sensor I wanted to use its mounted inside a 4" maf pipe and I am using a gen 2 translator .
when I select the ls1/ls6 85mm maf on the gen 2 I try to start the car but it does not start everything plugs in without issues. I have an lt1 maf at the moment and that works fine when...