Search results

I'm looking to upgrade to at least 80's, and I need to switch over to shorter injectors. $175 shipped to lower 48 Paypal, add 3%

BLUF: I need to buy a set of good used rear lowering springs, after finding out the previous owner of my GN cut the top coil off. Budget minded, will also consider new if at a decent price. Budget is busted after paying out of pocket for college classes. Thanks!

Since I've found the current LC2 in the car to be practically a boat anchor, and I've been wanting to experiment with an engine for years now, this was a good time to swap. Since there is no real dedicated section for this swap, and this may be the first of it's kind, I'll just open a thread...

Setting up my suspension and need some rough numbers before I set everything up and bolt the frame back on the car. What I need: Measurement in height to bottom of frame rail, nearest to the body mount just forward of the rear wheel and; nearest to the body mount just aft of the front wheel...

While I have the frame off the car, I'm going to perform a few budget upgrades. I'm looking for some specific set up numbers before I invest in upper balljoints. I will be using +.500" taller lower ball joints. I may or may not lower the ride height until I can view the car when It's put back...

Would it be a bad idea to solid mount the trans crossmember? Of course the ends would need to be modified to be rigid, but I was just brain storming ideas for a budget frame strengthening project.

Bought last year, less than 500 miles(probably less than 300) on this turbo. Billet CEA, Ported S cover, journal bearing, ported WG bypass to stock elbow swing valve. Don't need it anymore. Thanks!

When I bought the GN last year, the previous owner stated that the engine had been rebuilt back to stock specs, told me his father had it rebuilt about 5 years ago. Had some oil leaks I could easily address, but overall, clean oil on the dipstick and it seemed to run pretty smooth. Found the...

Any have pics or a legible diagram? The atsg is poor quality and the FSM I have isn't much better. In all my haste I tore apart the assembly without taking pics. I just want to make sure the sprag is freewheeling in the correct direction. Thanks

Anyone have a CK performance 2004R book they want to part with? Also would like to find an ATSG for the 2004R, and the video. So if anyone has those lying around, I'll buy if the price is reasonable. Thanks!

Looking for the 83 TTYpe I used to co-own, just curious to see if anyone here may have seen it around. Last known location was Richfield, Ohio. A former friend and I bought this car from a guy in Muskegon, MI back in 2003ish. My friend initially covered all the costs until 2005 when I...

I was considering replacing the voltage regulator in the 12SI with a higher set point regulator, 14.8V. Will this cause any long term issues with the electronics on board? Thanks

Kinda torn between installing an A2A intercooler(23.5"x12x4), or buying an Akly kit. Combo: Stock SLIC Stock bottom end Ported irons PTE 6262 turbo Hemco plenum EBL SFI 6 My budget allows for completing the machine work on the heads, and gaskets. I will have enough left for an alky...

Due to lack of local interest, I'm posting this rear brake kit here. When I bought the GN, this kit was in the trunk, never installed. Previous owner lost interest in the car and never got around to installing these brakes. I opened the box and checked the inventory and everything is...

Hi all Im going to dig into a set of 8445 heads soon, and need a little bit of guidance. First of all, im not going to buy champion irons, and any other expensive hardware. The set of heads I have seem to be in great shape, just need to upgrade the springs, that's about it as far as hardware...

IAC doesn't seem to be operating correctly, actually seems to be shut(extended) and not move at all. Swapped with a known good IAC and same result. Tested the leads for the IAC; Key on there is 12v+ at B&D, Blu/Blk strp and Grn/Blk strp Now it is my understanding that initial key off...

Just got my car on the road last week only to find out that 2nd gear is about toasted. Bad overlap and soft shifts. Before it completely breaks, im going to replace it with another trans with about 5K on the rebuild. A good friend of mine is giving it to me for a really fair price since I...

Just received the Dynamic EFI SFI-6 today(thanks BobR). So I will keep all the pics, videos, tuning Q's in here. Will also be using an MTX-L wideband. Going to get started on re-pinning the harness in a few.

Just found my turbo is toast. Looking for a decent used turbo at a reasonable price, still have stock converter, so I don't need anything bigger than a 62/62. Thanks!

As the title states, looking for one that someone has no use for, at a reasonable price of course. Thanks!