Search results

  1. H

    WTB: Gauge Ribbon Circuit (Behind Gauges)

    Looking for a nice gauge ribbon (plastic copper circuit thing behind the gauges). I have an 87 GN if they vary thanks
  2. H

    Anyone going to Kirbans have extra black carpet material?

    I always buy extra/bulk so i don't end up running short. I was curious if anyone has any leftover black carpet material that would match any of the black trunk carpet kits to wrap around the bottom and sides of my current sub box project? I think the trunk carpet kit manufacturer is R.E.M. or...
  3. H

    Black Trunk Carpet Kit

    Seeing if anyone has one of the black trunk carpet kits (embroidered if possible). Thanks
  4. H

    Test Pipe Block off cap for 4 bolt flange

    Does anyone have one or know who sells them before i have my buddy make one? I'm using the test pipe dump end with a turn down and would like to cap the 4 bolt end until i get sick of the noise. I measured 4-3/8" center to center on the top bolts and 2-3/4 center to center on the side bolts...
  5. H

    Molded Rubber on Factory Fuel Gas Tanks?

    Does anyone know what the sticky rubber pieces are on our factory gas tanks? I bought a spectra replacement and was debating on removing them from the old tank and putting them on the new one. If Im confusing anyone, they are the rectangular molded rubber pieces stuck on the bottom and back of...
  6. H

    Wilwood proportioning valve adapter fittings

    Hey Guys, Those of you running the wildwood proportioning valve, how did you adapt our lines to the 3/8-24 fittings going into the bottom of the prop. valve? I’ve been looking for adapters/ fitting etc with no luck. From what I gather our rear flare nuts on our lines are 9/16-18 and our...
  7. H

    Control Arm Bushing Heat Shield

    Looking for a used one in great shape if anyone has one. Thanks
  8. H

    Adjustable Rear Control Arms Setup

    Hey Guys, I’m currently installing Rear upper and lower Adjustable control arms and was wondering if you guys had any base measurements of more or less adjustment. The car is used on the street. I was going to just measure the Stock arms for a starting point unless you guys have any...
  9. H

    Stock Spindles

    Looking for stock spindles in good shape if anyone has a set laying around. I'm in NJ Thx
  10. H

    Need help choosing Wilwood Master cylinder

    Guys, I need some help. Im putting wilwood brakes on all 4 corners and am looking to change out my master cylinder to one of the wilwoods with the proportioning valve. My previous cars owner changed to vacuum brakes and I have no clue what car it's from. I took some pics but based on my...
  11. H

    OEM Transmission Crossmember mounts powdercoated

    I have a used set of oem trans crossmember mounts. The brackets were just powdercoated and the rubbers are all in great usable shape for their age. No cracking. Bolts were blasted and painted. Check out the pics. $60 shipped. Thanks
  12. H

    Kenne Bell KB Valve covers wrinkle black just coated

    I have a beautiful set of kenne bell valve covers I just had powder coated wrinkle black and polished the logo. Comes with chrome caps (no breathers) and bolts w washers. $180 shipped w pp fees
  13. H

    Rear Exhaust Hangers

    Looking for the rear Drivers and Passengers exhaust hangers over the axle in good shape with good rubber. pm me what you got. thanks!
  14. H

    Alradco Fan relay location

    i know a bunch of you are running these spal fans they sell with the shroud that fills the area behind the radiator. Alradco comes with no set area to mount the relays. However i can safely fit and reach all connections if i tuck them inside the shroud between the radiator. Im a little...
  15. H

    Electric Fan Setup

    I have an electric fan setup. ramcharger/ intrepid. Comes with caspers adapter harness plug n play, upper brackets and powdercoated lower bracket and hardware. Tested last night works great $180 shipped
  16. H

    F250 Trans Cooler with FMIC

    Hey Guys, I figure I would share an external trans cooler install I did on my car since I didn’t find any great options with also running a Precision Front Mount IC. Anyone looking to do this, I eliminated all the guesswork making your life easier. Long story short I went to go change my...
  17. H

    Reuse washers with kirban radiator support bushings?

    Title states it all. Just wanna make sure before i button this up i dont need to reuse the oem washers. Just use what kirban sent so im not doin this twice. Thanks fellas
  18. H

    Front corner 194 light harnesses

    can these be bought new? I asked napa and hes still looking. any help would be great, mine was a disaster.... see pic
  19. H

    New AC Compressor

    If anyone has one shoot me a PM. Thanks!
  20. H

    Precision intercooler fix

    Hey fellas. Im redoing some areas on my car and i took my precision fmic out and the top aluminum plate is bowed up slightly. Was wondering if any of you have had this issue and what the fix was? Should i cut an end and reweld it or just leave it? It doesnt effect anything its just cosmetic...
Top