Search results

For you guys running th400 what temps are you seeing? I have a FTI th400 with a 3500 non lockup stall. I have a deralle cooler with fan that comes on at 180 and also a heat sink. And here in florida it gets hot. I tend to see around 190-195 on normal driving but if i get on the car i can see...

Like the post said. I just installed a BMR rear anti roll bar. The installation is straightforward with no issues. However, i am hearing some noise as i back down my drive way. i checked under the car and don't see any obvious issues. The BMR bar is very similar to the HR bar. My question is do...

So a while back my 200r4 took a crap on me and after pricing the cost of shipping it out and upgrading to a stage 3 with a converter I decided to put in a th400. My new th400 is rated to about 950-1000hp along with the new converter. I figured this new transmission will last me a lot longer than...

Selling my Scanmaster 3. $175 Shipped. Absolutely no issues with it works perfectly. text me 4075094996 or PM me.

So i am in the middle of putting a Th400 in my GN and i ordered a HR Parts Th400 trans mount. I already had a HR parts 200r Trans mount in the car. But at close inspection both mounts look identical. However the box still said its for a TH400 on a GN. Are they actually the same part?

Ok after lots of thought I am going Th400 this week. I already have a Trans builder in mind. I wanted to know who would be the best person to contact to build me a converter. The car is not daily driven and will see some track time once in a while.

Well my 200r4 is out of commission going from 2nd to 3rd is just not happening and i am hearing a nice wine coming from it when idling. I am looking to switch it up to a TH400 but not really interested in spending more than $1500 on a transmission. I understand i need a new converter and it...

Like the title said i just recently downloaded windows 10 and my XFI is not wanting to connect. did a search and couldnt find any help on the issue.

Was out for a drive and noticed my break pedal going to the floor. checked under the car and noticed my brass Proportioning Valve was leaking from the nipple covered by the rubber gromet. Do i need a new valve or is it another issue i may have. Also i noticed none of the local parts store carry...

i tried searching but could not find an answer. i currently have .42v at idle and 5.06v at wot. i have already tried reseting the TPS twice and still the same issue gives me a fault code. all my reading are from my Scanmaster 3. Could it be the sensor is bad? thanks

I am going to Longwood tonight for the "Post time cruise cafe" cruisin. If anyone wants to meet me there. It's from 5:00-8:00 located at 2500 S. US 17/92, longwood

The car fires right up when i first start it, but when i drive it around a while and let it sit for 15-20 minutes and try to start it up again it cranks way to long before it finally starts up. Which after start cranking table do i adjust?

Daniel B aka (1987GNASTROROOF) is a awesome buyer, immediate response to all questions and pays fast with paypal.. I would sell to him anytime.

Stock Intercooler with shroud $150 obo Stock Valve covers $40 obo Stock TB Headers w/cross over pipe (never been welded but driver side has crack) $150 obo 36lbs injectors $80 obo SOLD Stock Dog House $ 50 obo Stock Throttle Body $50 obo Stock Chrome up pipe $40 obo Stock Radiator $45 obo I am...

I have a set of Comp 853 lifters that were purchased last October. i have a horrible ticking sounds that is coming from the passenger valve cover. When pulling the the cover i noticed about two different lifters have bad bleed down and will not keep the pump. i am about to pull the intake this...

Ok, so I have the noisy Comp Cam 853 lifters with the recommended 8.200 push rods that go with the Hydraulic 212/212 cam. I recently purchased there push rod length checker. Today I checked it on the base circle (for no up/down slack) and it ended up showing 8.225 length. My question is would...

I recently changed my OEM MAP line for a 3/16 rubber hose. I noticed the inside diameter of the rubber hose is larger than the stock hard plast line. Would this change how my XFI reads and give me a lean condition?

i am sure this subject has been beat to death with a looong stick but the search feature is not working right now. I am looking to upgrade my cooling system so here is my question, i am looking for the part number to the Dodge Intrepid cooling fan from Rock Auto, and the part number to the...

OK GUYS…SO IM LOOKING AT THIS AND AM NOT SURE IF THE ROUND DONUT LOOKING PIECE OF THE CAM BUTTON NEEDS TO BE A PRESS FIT, INTERFERENCE FIT OR SHOULD IT JUST SIT IN THE FRONT OF THE CAM. MY FEAR IS THAT IT WILL EVENTUALLY FALL OUT. IN THE FIRST PICTURE I HAD TO TAP IT IN WITH A HAMMER. IS THIS...

I did a search, however could not find anything regarding my question...i was wondering if the size of the line used for the boost gauge makes any difference. Reason i ask is because the autometer cheap plastic clear tube line kinks very easy and was thinking of using a larger 7/32 regular...