Search results

  1. F

    What Happened To Our Website

    Are the missing images gone for good?
  2. F

    Additional port work (finally completed)

    I should be at the meet on Saturday.
  3. F

    Additional port work (finally completed)

    Mike i think i am going the same route you did and porting my stock heads when i rebuild my motor so i am sure we will behaving alot of conversations on this topic... Great Job bud it is coming along awesome.
  4. F

    Do I need my factory harness?

    Did you replace this with another GN harness or a LS harness?
  5. F

    Finally getting closer

    Did you have any hood clearing issues with the high ram intake?
  6. F

    Th400 Trans temps

    I am running Synthetic ATF from FTI
  7. F

    Th400 Trans temps

    Thanks again fellas.
  8. F

    Th400 Trans temps

    I just checked both coolers are almost the exact same size pushing the same 500 CFM. So i will bypass the 180 switch to manual and remove the heat sink and see how that goes. I assume you have a similar stall speed that produces the same amount of heat. i think that is where the majority of the...
  9. F

    Th400 Trans temps

    Are you guys just running a single cooler? I am going to remove the heat sink but the reason i ask if a secondary cooler will help is because i already have one sitting around.
  10. F

    Th400 Trans temps

    What do your temps look like?
  11. F

    Th400 Trans temps

    I will give that a shot. Do you think replacing the heat sink with another plate & fin cooler will help also?
  12. F

    Th400 Trans temps

    For you guys running th400 what temps are you seeing? I have a FTI th400 with a 3500 non lockup stall. I have a deralle cooler with fan that comes on at 180 and also a heat sink. And here in florida it gets hot. I tend to see around 190-195 on normal driving but if i get on the car i can see...
  13. F

    BMR rear anti roll bar makes noise.

    I just ordered 1 3/8 two piece collar from amazon. According to BMR and HR this is a common thing with the anti roll/drag bars.
  14. F

    BMR rear anti roll bar makes noise.

    The bar is a solid 1.375 but i will give BMR a call first.
  15. F

    BMR rear anti roll bar makes noise.

    Now..where can i get a set of those anti walk clamps? Fantastic idea!!!
  16. F

    BMR rear anti roll bar makes noise.

    Yeah mine walked about a full inch or so. i think that was enough to bind the heim.
  17. F

    BMR rear anti roll bar makes noise.

    I think the instructions recommended putting the caps outboard to the bend but the spring base on the axle tube does not let the top half of the cap go any further. My only option is to weld the bottom half of the cap were it needs to be. i did notice the actual bar did move slightly towards...
  18. F

    BMR rear anti roll bar makes noise.

    Ok. I am going to have to move the hardware that holds the bushing outward closer to the bend of the bar. But it will have to be welded because the spring cup will not allow the top half of the cap to be attached in that location. I will also take another look at the heim joints. Thanks Mike
  19. F

    BMR rear anti roll bar makes noise.

    Like the post said. I just installed a BMR rear anti roll bar. The installation is straightforward with no issues. However, i am hearing some noise as i back down my drive way. i checked under the car and don't see any obvious issues. The BMR bar is very similar to the HR bar. My question is do...
  20. F

    Holley hi ram

    I know its a old post. But a friend of mine has the holley mid ram intake. Its the same as the hi ram but the lower part of the intake has shorter runners. And it fits great under the GN hood.
Top