Search results

87chrisss is a good guy id buy/sell from him anytime

scanmaster- 220.00 shipped mass air flow translater- 160.00 shipped 86/87 ECM- 50.00 shipped stock injectors and turbo TT chip for hot air- 40.00 shipped stock cam sensor works great- 120.00 shipped stock hot air crank sensor with housing- 60.00 shipped hot air TPS sensor- 50.00...

my car has no mufflers just a catyltic convertor. is it ok to just cut it off? i dont know if its even good anymore, maybe its plugged up? will the car get louder? im in michigan so no tests.

are all spark plug wires the same? can you use 3.8 n/a wires on a turbo car? i have a 85 and was wondering because i am chasing a bad idle problem i used them cause the ones for mine were out of stock and i figured all wires are pretty much the same?

well the cars up and running again without the white smoke :) but it still got that stupid shake to it at idle when ur driving it it smooths out very nice after 1500 rpms im using spark plug from an n/a 3.8 car cause they didnt have mine in stock and i thought all wires were the same but...

well i took the car to get painted at maaco and this is what i think really happend they drove my car and didnt know you had to hit a switch to turn the fans on and it overheated and blew the radiator hose open then they hit the emergency lights and drove it back to the shop. they call me...

just got done with body work and fresh paint job thought id let people see it. still not running 100% though , like it still has vacuum leak or something, only problem is i cant find it to save my life?? before passanger side rear wheel well after

when i was at the junkyard getting my 3" MAF sensor i picked up the caprice license plate holder and i picked up the alternator bracket off of a 3.8 NA cutlass. i did it not only because i figured i use an electric fan now and it cant hurt to have a bigger alternator for my 12 inch subs :cool...

i got translater and 3 inch maf sensor, does it fit the stock intake tube? what do i have to do to make it fit? the car is at the body shop right now so i cant test it myself. when people say my fuel pressure is 41 line off for example, what do they mean? 41 fuel pressure with vacuum line...

just bought one and its on the way. if i go to the junkyard from what i understand 94 and up 3100 and 3400 motors will have what im looking for. there are monte carlo and luminas everywhere so it should be cake. is the stock maf 3 inches? what is the size of the stock tube?

im interested in buying a maf translater. thank you

car is running way better now that i put a gasket on the egr. the leaks gone now and drives great but at idle im getting a little surge rpm will go to like 700 car will shake a bit then go back up to like 950-1000 then will run smooth at like 850-900 for a couple seconds, im still using the...

i bought a new borg warner ignition module, and caspers harness but it wont start? what could be the problem? i didnt try putting the old one back on to see if it would start again but im sure it would. only thing i can kinda think of is, on the plate i drilled three holes and only one was in a...

what is the hotwire for in the ignition module adapter

i noticed on this persons picture that his plug wires are on the opposite side of mine which is the same as what the sticky says. he has the upgraded coil probably the module too, i just have the newer coil cause nothing was wrong with my module. how should i have my wires?

Car idles like shit,,, il drive it and it drives pretty good but then after like 15 min of driving it starts to stutter then dies,, il pull over and check stuff over everything seems way hot, I got a temp gauge and it stays at 190-210 but it has new 160 tstat ,,, water pump only has like 5k...

I make the car top dead center, then I rotate it, standing in front of car facing motor, to the left(as if I were loosening a bolt) 1.45 inches. I drop cam sensor in gear dot towards pass fender and wires towards driver headlight then I turn clockwise to 7 or more volts then counter clockwise...

when i put my engine together i never put a knock sensor back, i didnt know what it was and didnt know i needed it.... does it have wires running to it? how exactly do you install it? im gonna buy one tomorrow

i took mine out and put a water temperature gauge in the hole instead, now after reading ive found the ecm actually takes into account what the water temp is. is it ok to do what i did or should i put the old one back? i dont have a scantool yet but after seeing how sweet they are and handy i...

is there any way to adjust the IAC on these cars?