Search results

I purchased his kit directly from Julio about 7 months ago. Just opened the box for picture's, never touched and never installed. Dual nozzle kit and I am including my ac delco 3 bar map that is used but works 100%. $550 I am in NY if anyone is local

My harness grd wire is shot and tearing from connector that goes into window switch. The Dorman replacement is garbage and piss poor design. Does anyone else make a quality repo??

Hey guys, My IAT is in the plenum and I am surprised what it is reading. It is about 25 degree's above ambient while crusing and hit 115 degrees while being at a red light for 2 minutes. It is a front mount setup on E85. Does this sound right? It is a older GM sensor. It is 65 outside and it...

Hey guys, took my dash panel off and found this connector just hanging . It has juice with ign on, any help is appreciated. Cannot find anything that would connect to it.

What garbage. I purchased the kit from Brian at Bowling Green this year. They do not have plastic inside of them for support at the screw mounts, just some cheap shit little washer. Not only is my "heavy Duty" door weather stripping already tearing at the washers but now the window one is to...

Hey guys. Highway stars has none in stock. I am looking for hood and fender emblems for the GN and see prices all over the place. OPGI has them in stock but says nothing about them

Selling my MSD distributor with 2 ignition boxes, 2 coils, 2 sets of wires and Hartline performance coil pack harness terminator. Everything works, I had the dist and crane box running with my fast classic system for years with no issues. If you going to hook this up to a seq DFI you going to...

Hey guys, if anyone can help me with this I would deeply be appreciated. When using a msd Distributor with a factory crank sensor do you have to use a "Jumper plug" to connect distributor to cam sensor harness? Do you also need to cut all but one of the reluctor tabs? I have the dead end...

I heard several people over the years that the Summit racing brand bushings (Grey) was a softer durometer then the other companies. The kit comes with every bushing, bumper to bumper but no bolts for a good price. I got them installed in a few hours and I am very happy with the ride quality. My...

Looking at a 22 acre lot in Cassatt , SC. Curious on your opinions of the area etc etc

Hey guys, Took my heads off due to oil leakage between the layers of copper on the gaskets and noticed all of them had this issue. please look at pic, the copper seperated at several locations near every bore. I have champion heads, arp studs, torqued to 75 ft lbs. The gaskets are for the...

Hey guys, a car dealer in Volo,IL is selling a badass 1967 Chevelle that I am very interested in. Unfortunately it is 850 miles from me so I am hoping to find some one in that area that can check it out. I am looking for possible hidden damage , questionable work or hidden rot(especially under...

Moog problem solvers (K5208) roughly 8 years old. Mounted on the tubular upper control arms GBody Parts sell's. Car drove really funky, de-ttached and dangerous, did some investigating and found this on BOTH sides. Ever see this???, BTW< boots were filled with grease, no rust.

What a waste of $1500. I was fooled into buying Martelious- exhaust headers with all the fancy pics. First set the flange would not even line up with the head bolt holes. After laying 55$ in duties the second set was worse! I finally messaged them to fit and after driving 150 miles the crossover...

hey guys, installed Moog 5606 in the front and K160044 in the rear . Torqued control arms to 70ft lbs with weight on them, springs are installed properly (triple checked) white mark is top top and bottom seated properly and lower control arm hole is visible. The pass front is 3/4 of an inch...

I installed front springs (Moog??) several years ago and cut 1 coil off to lower the car. Love the stance and ride but the car always made this funky noise like the bottom coil is re-seating into its pocket of lower control arm? It is a heavy ping noise. Happens ONLY when I lower the front of...

I need to know what ball joints are being used. MY moog's say 5730 on them with the DS marked 18 and the PS marked 19. Any pics of arms installed would be appreciated as well. Trying to fix my turning issue, possibly an issue with A-Arm install.

Anyone have any laying around?? Please let me know. Should say 7828464 + 3 on the bottom of it. thanks Ralph

Hey guys, So our cars (12.1 ratio) come with a pitman arm that is marked "7828464 + 3" What is the difference between that and a "7828464 + 4"???? I am having a steering issue with my GN and trying to figure it out. I might NOT have the correct pitman. Any help is appreciated!!

My Fireball Hi-6 has possibly taken a dump after 10 years (No spark cond even with new coil). It seems like they dont make ignition boxes anymore? Although FAST has boxes that look like my HI-6? What gives? Anyone know?