Search results

I've been doing a bunch of wiring lately and eventually realized that I had "folded" the ribbon on the back of the gauge cluster shorting out the fuel gauge connections and lights. Now I have all that fixed, my fuel gauge doesn't seem to be working (sits at 3/4 when tank is full). In the gauge...

I didn't build this, it came with a gauge cluster I bought from a member a couple of years ago. I finally got around to getting it installed.

I bought a stainless converter hanger from G-Body parts a while back that I can't use with the 3 inch downpipe. I assume it will work with stock exhaust, but it wasn't even close to reaching the converter flange on my setup. I had to fabricate one that was about an inch longer. New they run...

I am looking for a 3"stainless test pipe. Doesn't need to be polished or anything, just needs to have the 4 bolt converter flange on the back. Please let me know what you have and how much you want for it. Thanks.

I ditched my stock draw-thru carb setup a few years ago and after having power, there AIN"T NOT WAY I'm going back. Going back to stock isn't an option. So, I have a bunch of spare parts for the carb engine, so hit me up with what you need. 1 complete engine that ran fine and a cabinet with...

I have been collecting parts for the past few years since I started the restore on my 83. I considered keeping the original draw-thru system just because it was kind of unique, but it was tired and I was ready for some fun. The parts list: Basic 109 block bored .030 over. Older GN1 aluminum...

A few mods to the oil pan. 1: Closed off the original drain plug that stuck up into the pan preventing the stuff in the bottom from draining out. New one has the threaded bung on the outside so it is flush with the bottom inside the pan. 2: Turbo drain tube attached copying Earl Brown's...

I'm adding a 36-1 trigger wheel to my build and needed to fab up some type of mounting bracket for the sensor. The sensor has to be 6 teeth before the "missing" tooth. My mistake was putting the missing tooth right a the TDC timing mark. I mounted the trigger wheel to the balancer that way and...

I am selling a set of T&D 1.60 roller rockers for iron heads. They don't line up right on GN1 heads because the valves are spaced farther apart. Some people say it can be made to work, but I'm not going to try. I'm just selling these to get the right set. Supposedly there needs to be some...

It appears I need a set of roller rockers for GN1 aluminum heads. The set I have don't line up and it appears they are for iron heads with the closer valves. Will trade these + $$, or just $$. Please let me know what you have.

My mufflers have finally bit the dust (split out the bottom). Installed by Midas in 1995 with "lifetime" warranty. The shell is only about 10" long with a total length of 15" and 2.25 inlets. They can't find anything the same size to replace the mufflers. I have scoured the internet and I can't...

I want to add a little "thump" to my Regal. I figure that 2, 10 inch subs should be able to fit nicely against the back seat. I don't need the kind of bass that rattles the license plate, but at least something you can feel. Speakers have single or dual voice coils, I don't know what that...

https://www.autobidmaster.com/en/carfinder-online-auto-auctions/lot/26687919/COPART_1986_BUICK_REGAL_T-TY_CERT_OF_TITLE-SALVAGE_VEHICLE_DETROIT_MI/

https://www.autobidmaster.com/en/carfinder-online-auto-auctions/lot/28904469/COPART_1987_BUICK_GRAN_NATL_CERT_OF_TITLE-FLOOD_SALVAGE_MEBANE_NC/

Body rough, but appears to have engine mods. https://www.autobidmaster.com/en/carfinder-online-auto-auctions/lot/43573028/COPART_1987_BUICK_REGAL_CERT_OF_TITLE-SALVAGE_MINNEAPOLIS_NORTH_MN/

Purchased a mini-starter from Turbo85 a little while back. All went well!

Bought a tensioner off of Vinny. Thanks!

I have a set of Royal blue upper door panels that I bought a while back from Fat Nat. They are new in the box originally purchased from Highway Stars. Apparently I need "Navy blue" instead of "Royal blue", so these won't work for me. Stitching is white and holes will need to be cut to fit...

I bought this manifold mid summer from Steve and build changed directions. Complete stock intake manifold. It has the lower intake, plenum, fuel rail, and Throttle body. $225 plus shipping Throttle cable bracket is not on the doghouse and the little "arm thingy" isn't on the TB. They weren't...