Search results

  1. H

    Scanmaster G reading

    Just hooked up ScanMaster, This is my first time using. Any comments are appreciated. I had readings for Spark Advance 71.3 & Injector PW of 55.5 This only shows up with ignition on not running( is this correct?) Below are my numbers, looks like my IAC is high? 10-20 preferred? Any other...
  2. H

    1987 Gn is sputtering

    I was referring to my emissions numbers, amazing how much older gas can effect emissions. The car was still running good at the time it was tested. It just started running bad sporadically as I drove around town. I think my Fuel Pump might be going bad or have a restriction, pressure is ok at...
  3. H

    1987 Gn is sputtering

    Guys, My car is giving me fits. Shame on me for not driving it enough. Here is a list of things I've done recently: About 2 years ago I replaced ignition module, coil pack, plugs, spark plug wires, new injectors & matching chip from Turbo tweak along with new injector harness. Also put in new...
  4. H

    need help troubleshooting bad running engine

    ok Thanks, I need to order a new Turbo Tweak Chip & Injectors, to get up to date,
  5. H

    need help troubleshooting bad running engine

    Sorry I intended to say: I would be better off buying a new 6.25 version MAF "Translator" no wire splicing needed?
  6. H

    need help troubleshooting bad running engine

    Found my older LS1 MAF 3" sensor & MAF Translator plus(version 4.0). I wanted to install to see if the MAF sensor is bad, but before I do this I have some questions. As of now I can not find the original install instructions but I do remember I had to splice into the wiring up towards the...
  7. H

    need help troubleshooting bad running engine

    Found my older LS1 MAF 3" sensor & MAF Translator plus(version 4.0). I wanted to install to see if the MAF sensor is bad, but before I do this I have some questions. As of now I can not find the original install instructions but I do remember I had to splice into the wiring up towards the...
  8. H

    need help troubleshooting bad running engine

    Found my older LS1 MAF 3" sensor & MAF Translator plus(version 4.0). I wanted to install to see if the MAF sensor is bad, but before I do this I have some questions. As of now I can not find the original install instructions but I do remember I had to splice into the wiring up towards the...
  9. H

    need help troubleshooting bad running engine

    Found my older LS1 MAF 3" sensor & MAF Translator plus(version 4.0). I wanted to install to see if the MAF sensor is bad, but before I do this I have some questions. As of now I can not find the original install instructions but I do remember I had to splice into the wiring up towards the...
  10. H

    need help troubleshooting bad running engine

    stock - AC Delco Been keeping the tank fairly low, and adding fresh gas now & then when taking it out (non-ethanol) I have a new fuel filter I will put on. I have an older MAF translator & LS1 sensor that I tried years ago when they 1st came out for the Buicks, I did not like the way it ran so...
  11. H

    need help troubleshooting bad running engine

    My 1987 GN has been sitting for a while, and really not driven a whole lot in the last ten years, other than around the block for short rides. I was hoping to get her cleaned up and start driving more often, it was my daily driver years ago. the car has some nice upgrades and has always ran...
  12. H

    back up lights

    back up lights fixed Thanks Guys, The link supplied by Thecatman was right on. I loosened the bolt on the cross rod underneath the car and moved the linkage until reverse light came on, then re-tighten bolt, very easy. With the help of my 11 year old son it was done in 5 minutes. Thanks again
  13. H

    Dell latitude with turbolink

    I think I have what your looking for. I will look tonight, and if so will contact you regarding a trade. Thanks, Eric
  14. H

    back up lights

    Back up lights come on when car is put in neutral instead of reverse, where is the adjustment made to fix this? Thanks
Top