Search results

Downpipe end is 2.5" for stock dp with cat back flange and dump, no dump cap.

I bought a stock car with 22k miles and it had these plug wires on I replaced with stock size 8mm. I would guess the third owner installled these cause internet research shows them coming out in 05 so they should only have a few thousand miles on them. New price $30 shipped. Tim

Years ago I purchased some correct length black plug wires for about $35 from a vendor. Anyone recall where to get these or where to buy some decent ones for a stock TR? Which plugs are recommended now also?

I sold my car a year ago. I have stock headers, 2 starters, a compressor, some brake pads, misc, etc. I'd give it to someone that could use the extras, but you have to take it all. I am cleaning out my garage, this fits into a few small boxes and thought I'd ask before throwing it away...

I have this in two large three ring binders with each of 9 sections marked by divider page tabs. $40

This came with my car and I upgraded to the 9500ix. I have the coiled smartcord with it too. $250 shipped. There is a button on the top where it slides in that is missing but the unit stayed secure for me. I have paypal also at tim87tr@yahoo.com or email for address for MO

UMI performace round drive shaft loop with hardware, $45 shipped 48 chrome up-pipe with alky hole drilled, $45 shipped 48, will include the two hose connectors with two black pipe clamps each. Hoses are the good ones black on outside and orange on inside. Pipe has some chrome flaking where...

Art Carr 16930 9" n/l TC, 3200 stall. Less than 2000 miles since inspected 5/07. Was a great street/strip TC. Only made about 10 passes on it, half were 1/8th mile. $425 Built Bowler trans with parts listed below for n/l TC. Same miles and passes as convertor, no issues. I ran this trans...

This is probably the wrong time of year to sell, but I've owned the car 8 years and thinking about selling the GN or WTT for 06 Trailblazer SS AWD for a winter vehicle to upgrade from a 94 s10 blazer (trade stock also). I have a word document fact sheet with all the mods on it I can email...

I have a stock engine, Powerstroke IC, Razor alky car with a TA 49 and D5 and running 20 to 22 psi and might bump it a little when I get to the track. I have considering trying my spare trans and n/l 9" TC, stall should be around 3000-3200. Is this too much converter or possibly I should go...

2005 Cyclone Gray Metallic M6, 20,600 miles, Kooks stainless long tube headers ceramic coated black with high flow stainless midpipe cats, JBA mild catback, GMM shifter, TSW Vortex wheels, cold air filter, King springs, BMR strut tower brace. It has the black grill and hood inserts that are...

I just swapped over to vacuum brakes, and had bought a new accumulator from Kirban to diagnose my powermaster, installed once, moved out of the garage, and back in:D I also have another Kirban accumulator that I used for a couple thousand miles possibly. If you need a spare, these are a...

I have two C16 race chips for 55s high impendance injectors for sale 1. Red Armstrong R106H Race Chip-$30 shipped 2. Turbo Tweak 27/26 degree 25 psi race chip-$30 shipped (never used) Both chips package deal $50 shipped...

It has a Weber 206 roller cam and Dave Weber ported and O-ringed irons, std bore and crankshaft, TRW pistons with light weight pins, and steel main caps. Last year at Morocco, IN, I drove the car with this roller cam engine 100 miles to the event, and it ran 11.01 @ 121.9 mph right off the...

My PM motor went bad and I installed a low mile complete PM system. The brake pedal rod seems loose after I attached it to the pedal and the pedal is completely soft, and I started to bleed the system which didn't help either. Does this rod attach internally in the master cylinder body area...

I just finished using the H&R bushing removal and install tool and it worked real well on the rear end housing bushings. I paid around $100 shipped for it and I'll take $65 shipped for it. You can use it, and re-sell it without as much loss as I'm taking. Also have 1. one set of stock...

I damaged the small metal wire plug for the gray parking light wire that plugs into D11 of the ECM for the Extender Extreme. Any idea where to find one of these or is there an alternate method I can use to plug this in?

To replace my warped rotors, I've finally bought something I've wanted to try for awhile, Powerslots. I've used the Morse ceramic pads from Autozone on my other cars with stock rotors, and liked them enough to use again. Of course the Powerslot rep recommends Hawk pads, which is a sister...

New in bag control arm bushing heat shield for upper control arm passenger rear bushing to protect it from the THDP heat. Yes, it does get fried and I have an extra I never installed on another TR. Includes 15/16 special lock washer and slim nut to attach and install sheet with pics. $25...

I will be taking this IC off my T-type in a couple weeks because I am selling my car as a roller. I was told when I bought the car that it was called a Buza. The story I've heard is that this guy used to work for Mark Jackson when he made ICs early on and then he went off and made his own. It...