Search results

  1. O

    FMIC

    i have a universal fmic tht cxracing.com sells . i never used it just test fitted it ..diminsions are 25x18x4 ..INTERCOOLER ONLY..sells online for $201..i sell this one for $125 shipped
  2. O

    high maf reading at idle and trouble code

    Ok I purchased a MAF translator and a LT1 sensor ..my MAF was reading around 13 with the stocker..put the new one on ..well no change..my blms are low at 105 and I'm getting a MAL code 45 . I have no idea where to go from here. As you can imagine my car runs like crap stalls/stumbles . Can...
  3. O

    High fuel pressure problem

    I recently replaced my stock fp for a walbro unit..I started the car and my fuel pressure is at 70 psi at idle . I have an adjustable fp regulator ..vac line on/ off makes no difference..nor will it go down turning the screw..I'm stumped..regulator worked fine with stock pump ..and ideas /...
  4. O

    LC2 complete motor 109 Block

    This motor is out of a 1987 Buick Grand National (mileage unknown). It has stock ported heads with ARP head bolts, 42 lb injectors. Everything else is stock. Ran well while in the car ..selling to finish my stroker motor..$1500 more pix by request
  5. O

    Scanmaster #s ...need advice

    Ok guys here is my deal ..I bought a 87 with blown head gasket ( super deal) . I fixed tht and started the car here are my numbers at idle af-14, l8-70, bat-13.3, int-128, bl-128, mph-00, cit-70, als-66, r-1200, tps-1.02, iac-174, pl-140, mal-13. From my readings these numbers are way off ..it...
  6. O

    No Start...

    I changed my headgaskets myself and re installed everything to the best of my ability. And guess what ..it wont start..not even a sputter..it just spins. I tried starting fluid ..still nothing. seems to be getting no spark..any suggestions ..i am a novice so any advice will be helpful..and is...
  7. O

    Comp Roller Cam Install Question ???

    I am thinking of installing a billet roller cam in my GN ..I bought champion iron heads so i think its only right..but i could be wrong..i have no problems out of my flat tappet cam, besides the fact that its 25 years old. To make a long story short I have no idea what im doing !!!..I have the...
  8. O

    Engine builder in georgia ???

    Looking for a GN specialist in Georgia or surrounding areas. When i tell my local builders i have a 3.8 turbo they look at me like im from outter space or something. All help and any help will be helpful I know about Southeast Turbo but they are pretty expensive..I was seeing what else if...
  9. O

    Wiring Troubles ???

    Ok I have swapped my drivetrain into a donor 85 buick regal limited. Outside of my downpipe clearance everything has went smooth. Besides now its time to wire her up. And im novice on grand national wiring. And and ALL advice will be helpful. Maybe even a wiring diagram. I still have my...
  10. O

    engine swap

    Ok guys I have a mangled 87 t type with a great drive train..I was thinking of swaping the drive train into a 87 limited that I have ..just wondering the degree of difficulty considering everything that will have to be swaped ..any help would be welcomed...thks ...
  11. O

    power seat?

    If I have a drivers bucket seat that is manual and in need of new track..can I replace it with a power seat track? May be a dumb question but I would like to know b4 I buy one ...thanks ..
  12. O

    Grey T-type seats

    I have a clean set of grey t-type seats. Its the front buckets and the back. Very clean . Pics real soon ...$250.00 for the set Loganville, GA
  13. O

    Greenhorn!

    Hello, im new to the site and to the GN world. I have a 86 GN bone stock. I took it to the dragstrip and posted a disapointing 9.01 in the 1/8 at 76mph. I see u guys have alot of knowledge on this site and advice would be appreciated. For starters, what are some things i can do to get my time...
Top