Search results

Not saying you cant build one to take the grunt but at what cost? The amount of hard parts you need to keep one healthy compared to a basicly stock 80e is not worth it. With the glide in ours it doesnt even feel like a 2 speed. Ive run 9s off the foot brake taking off in 2nd.

what did you use for the 80E conversion? Just a TH400 adaptor? The 60E are a joke over 400hp. We went straight to a glide. 80E be a good idea for a street car thats for sure.

Nice work! Do you plan to re-torque the heads? It helps the commetics seal if you retorque them when the motor is warm.

800whp block right there. Sorry about the slow reply, I see you went with the stock crank. They are mega strong. I have a stock uncut that had done 280,000km before id used it. We're still using TTY main bolts too lol... I never bothered to remove the balance shaft, just took the gear off and...

Cranks are damn tough. 800whp isn't a problem as long as the tune is good. I've been 8.81@158 so far using a stock (not even machined) crank and block. Just forged pistons and china rods. The cross bolted mains and deep block design is very strong. As you stated the only issue is the head...

I could do a stock coil on 28psi at 500-600hp but no way at all could I do it on 28psi at 850-900hp. Not all 28psi are the same. What I found using stock ignitions is you tend to have to lean the mixture to get a clean fire. With a cdi I can fatten up the mixture and make more torque.

I can make a seperate map for them. Bring them on at low boost. Probably just get another set of ids. They seem to be well controlable.

Just noticed this lol.. That is our quickest to date. Went 8.9@152 so I added some boost then 8.9@154 then more boost 8.9@156 and a little more, 8.81@158. Had more mph in it but couldn't get it to go faster ET wise just the mph kept climbing so gave up that day lol.. Factory stock rear...

Not looking for a duel fuel system or to buy injectors I can souce if I need. Thanks anyway. Was just wondering what guys are using when runing 12 injectors simultainiously with e98. 50psi is close to 4bar pressure already... Injector Dynamics said I can safely run them up near 80psi if I wanted...

87%dc at 50psi base pressure. Id2000 injectors. Think they are 210lb rated. Car went 158mph with a lot of tyre turning. Dont know what hp. I want to turn up the boost but dont want to put these injectors up in the 90% range. Afr is 10.6-10.8 consistantly. I guess easiest fix is to just bump fuel...

Hi need to move to 2 fuel rails very soon. What are you guys using for 2 sets of injectors? ATM have id2000 at 87% duty @50psi. I have already upped pressure from 42 to 50 to get more ceiling. Debating whether to move it higher or move to 2 rails. Advice?

Id remove the boost control and tune it on just gate pressure first to make sure it aint a gate issue. You may not have enough spring pressure to hold the gate shut at higher boost pressures.

Id say if someone had the cash and the will a series 2 block could go over 1k hp. They are stout. In the future we may give it a go.

Im using china spec h beams at close to 800whp. Good tuning keeps them alive. Matt Stattama has been 8.65@158 with the L32 rods. Dont really have any better sources for rods than you guys do. Zzp, mace and PPM all sell the same china rod for $600 od dollars.

Ive used them at 550 wheel hp. No problem. Transbrake launches at 26lb. Smaller setup than our current one. Still went 10.0@138

If I were you guys and you wanted to do one of these on the cheap, chase down an L32. They come with a decent rod, kind of like the GEN4 LS rod. Ive used these rods in some big power builds. They you would only need a set of pistons and a good hone to spec.

sorry for the late response. We use the stock block and mains with factory torque to yield bolts. Stock crank ( virgin, not ground ). Standard ACL replacement barings. China rods with ARP2000 bolts ( resized and balanced ), Arias pistons .020" Cometic head gaskets. Intense cnc heads ( could be...

Were using id2000 with ethanol and 60psi base pressure and car idles ok at 1000rpm. Big cam too. @60psi they have been flow tested to be around 250 lb.

Our stuff is quite bodgy compared to some of the stage 2 stuff on here lol.... Some are crazy! Yeh looking for 165-170 hopefully. They are a strong little motor that's for sure. We made 717rwhp and 805ft lb torque on a once off dyno run but I noticed when I got home that for some reason he only...

We take on 99% of the LS based stuff here and win with the little 3800. Ok the LS stuff is cheap but soooo boring. Every second car has one.