Search results

Does any vendor make a 2-piece valvecover? Would be great to just lift the lid off and check the valvetrain, Pulling the entire valvecover off just sucks.

I would like to remove the translator Plus from my Buick. I need to know if I can just make a jumper to plugin where the timing from the translator connected to the module so that the ecm would be back in control of the timing. If not then what would I need to do? Thanks I tried the search but...

Need a GN or Turbo Regal passenger side inner fender well shipped to 29906. Needs to be very nice or new. No cracks and I will need a pic or two of it. Before we have a deal. Thanks

I have an EXTENDER EXTREME CHIP now with 55lb injectors. I would like to change out my low Z computer and add 80lb injectors. Would I need a New chip or to have this one reprogrammed? I also have the Translator + and would like to move to the Gen 2 anything I should know before such a move? Also...

I have got my car ready for the summer, But the blower motor wont blow. I found that the ground wire at the blower motor that plugs into the connector at the fender has no wire on the other side of the connector? This would be the side that goes to the actual ground point on the car. I have a...

I have had my Car in storage for about two years and have decided to bring it back out for the summer. After looking everything over I can't for the life of me remember why I would have set the WOT dial in the Trans Plus to number 8 NOT USED? Can anyone tell me why one might use this setting...

I have a problem with my wipers hanging on the black metal shield at the bottom of the windshield. Anyone know how to fix this? Thanks

I have one in my car. It's just an electric one. My question is can I just lengthen the wire (add a piece to it)so I can reroute the wire? Thanks

How can I tell if the rocker arms or shafts are worn out? What is the signs of a rocker arm that is bad? Would I need to use a micrometer caliper? Thanks for any help.

I need to remove my fuel injectors is there anything I need to know? I have never done it before so any info is greatly appreciated

This is what I found today looking at the car. This is where the downpipe hooks to the turbo. My Questions are... Could this make a ticking/tapping sound? What other problems can it cause? What can I do to fix it? Also what should the bolts be torqued to that hold it to the turbo? Thanks for...

How can I tell if my ignition module and coil are AC Delco or generic?? I can post pics of what I have if that helps.

I need to add some fuel at idle and I'm not sure how to do it. Does anyone know how to do this or where there may be some pics of how to do it? I have opened the translator box and looked at it as well as downloaded the manual for it ,but just can't get it right. Also was not sure if this...

Ok Guys I need just a little help on this. I have put in a new cam sensor by marking the old one and putting the new one in the same way.I think it's right? My first time doing one. The car starts and runs, But feels like it is missing or sputtering a little. Could the cam sensor cause this...

When testing plug wires with a multimeter what should the reading be for good wires? I have used search and found nothing on this. Thanks

To give some back ground on what is going on. The car ran fine started fine but the cam sensor was tapping. So I said hey I'll put a new one in. I got a new GM sensor and marked the old one took it out and put the new on in. Now the car will start but shut right off after like 5 seconds? I...

I will be changing out my cam sensor to a new GM sensor this weekend and would like to know what all I will need to remove from the car to do this repair. Would a distributor wrench help with this repair? If so what size is the hold down bolt 9/16 or 1/2 ? About how long should this repair take...

How can I tell if the heads on my motor are Champion iron heads? I have looked at the side and they don't say champion on them?(that I can see) I was told by the person I bought the car from and the shop that built the car that it has them?? How do I find out what heads I have? Thanks for...

Right now I have 853's in the engine. I have a lifter that collapsed and was thinking I would go with a solid lifter. Is this a good idea? What would I have to do to make the change? Thank You for the help

Does anyone know of a place close to Charleston SC that I can get my car smoke tested. Maybe someone has one I could rent for a day or two? Thanks for any help