Search results

Guys that run nitrous and alky, where are you mounting your nitrous nozzle. Before the alky nozzle? After that alky nozzle? In the plenum? Wet or dry kit?

using the tach on the scanmaster, stalling 2450rpm with a gt6152. I have put about 10,000 miles on it. Not sure how many the previous owner put on it. Not sure what these are going for nowadays. Any fair offer takes it.

For the 200r4. Something that is in decent shape.

Stock Driveshaft I had it cut 1 inch, rebalanced and painted about 5 years ago to use when i swapped over to a th400. when i switch over to a th400 and have gone less that 500 miles since then. Maybe 20 mid 11 seconds passes since then also. Comes with a good 1330 joint on one end and a 1330...

What master cylinder are you guys using for manual brake setups? I have the firewall plate from dragracebrakes. I was reading that some are using a master cylinder off chryslers? I have s-10 wheel cylinders in the rear, stock up front. I have removed the stock porportioning valve, Teed the...

Hey guys, im currently in raleigh checking out the area and so far i like it and would like to move here. whats there to do in the area? any dragstrips close by? Whats the car scene like? any help would be appreciated. TIA

i got some parts here that need to move. heres the deal. i banged up a few pushrods in this motor. and im parting out the motor. these parts dont have much more than 3500 miles on them except for rods and pistons. i found no shavings in oil and bearings i looked at were ok. eagle crank already...

eBay Motors: Buick Grand National ATR double pumper (item 220086769402 end time Mar-05-07 15:06:13 PST)

eBay Motors: Buick Grand National Deep sump oil pan (item 220085933316 end time Mar-03-07 08:04:56 PST)

eBay Motors: Nissan : 240SX (item 140070817408 end time Jan-13-07 09:04:38 PST) This was from locals around here, money from car going to charity. bid up!

for stock style head. Used 3500 miles, one season. Going different route motor wise. $375 shipped to the US 48.

less than a year old. GM part #12223861 $50 shipped to US 48

all these items are a few years old at most. Accumulator ball $75 billet aluminum thermostat neck $25 2 boost solenoids $40 each "y" cord from turbo to solenoid and acuator $10 volt blaster (tps signal activated) $40 belt tensoiner with pulley $80 blower motor with 2 resistors $30...

I got a really loud noise at idle and gets louder with rpm. So im thinking rod bearing. well i pulled the passenger Valve cover and found the #3 exhaust lobe is probable wiped because the pushrod is missing, but i can see it down under the intake. Would a wiped cam cause a loud noise like a rod...

As the title says, Used but still in good condition. I took this off because i switch to a transbrake which is full manual. I have the stock 200r4 kickdown cable hooked up with the modulator that i will include. Also include a th400 vacum modulator. Pic availible apon request. Asking $100...

I just got a deep oil pan from a fellow board member... is a pickup tube extension needed for no girdle? or is it best to put a an extension on? and where to get one? TIA

i see theres 1.55 , 1.60 and 1.65 whats the best for performance? What would be the best to use with 218/222 cam and ported heads?? TIA

Looking for one with no cracks in decent shape.. paypal perferred.

How strong is the stock crank? and how much can it be turned?? i spun some mains again and not sure if the crank can be saved this time?

Have a ATR 7th with 30lb injector.... No led, but the wires are there if you want to hook one up.. I also took apart the box and bypassed the vacuum switch so it runs all the time... (full time 7th) asking $130 shipped to the US 48. paypal accepted