Search results

Normally I'd put my FS stuff in the FS section but since it's carb turbo specific I thought I'd put it here and if it gets moved that's fine- I put this 'rally' gauge cluster in my century Wagon and picked up a sport coupe cluster for parts. I sold the car as a roller and kept the cluster as...

Just finished my swap and dealing with a dead miss on cyl 1& 5. 4.1 with a 86/87 setup in a G body cutlass. I had pieced the setup together out of boxes that I bought from the guys widow. I had the engine in another G body running for 2 years with about 8k miles on the setup and pulled the...

I ended up with a center console missing the lid. Looking for a center console lid for a 78-87 buick console. I'd like one in red/claret/maple to match this but any color will do.

I put together a 4.1 SFI setup that I swapped into an 80 century wagon this winter. Fresh rings and bearings, dingle ball hone on a clean 4.1 .030 block, hyper .030 bottom end, stock LC2 setup (turbo intercooler ect). Maf translater with LT1 Maf, l67 injectors at 4 BAR with adjustable FPR and...

Looking for one of the old style bosch adjustable fuel pressure regulators. I am running AN lines and flipped the stock regulator upside down to clear the AN 90 to the intake. A newer billet or other regulator I believe is too tall. Must be one of the older bosch block factory appearing fuel...

Looking for a 91ish octane street 36 or 42 lb chip for my 86/87 setup before I buy a new one. I'd prefer non alky but if you have an alky one I'm still interested.

Hey B4B people, long time no visit in this forum. :) Been busy with my LS 2+2 and LC2 swap on my century wagon. My drawthrough cutlass has been sitting in storage for 2 years. Did a quick tachometer install on my century wagon and thought I'd put a how to up for a factory appearing dash. Its...

I have an LC2 setup I am swapping into a 80 century wagon. I bought a pile of GN parts (intake, harness, manifolds ect) minus a long block a and bolted all the GN stuff on a fresh 4.1 I put together. I have a CRF code 2004r I have laying around from my 305 SBC 86 grand prix 2+2 that I bolted...

I am LC2 swapping an 80 century wagon. In need of the dash harness, speedometer cluster, cruise parts, light switches, guage surrounds, bezels, ect. Basically need everything minus the dash pad itself and any of the HVAC stuff. Rather not get nickled and dimed to death so if someone is...

Need a stock GN throttle body blade. The actual blade only (and screws too but no bid deal if you don't) My throttle body blade was missing when I bought it. Thanks

When I was like 12-13 there was a blue malibu wagon in town that was pretty toasty but I still loved how it looked. Wanted a GN for my first car when I was 15 but didn't have 10 grand for one. Didn't know what a G body was I just liked both at the time. Ended up building a drawthough cutlass...

Edited 8/4 Selling a 484 4.1 block that is 30 over. It was missing 1 piston when I bought it so that bore has moderate surface rust on that bore the whole way down the cylinder. Other 5 cylinders have light surface rust on the top half or so due to sitting with no heads for 5 years or so. The...

This is an oddity. Anyone ever seen or ran one? Be interesting to run one. http://www.ebay.com/itm/Voffenhauser-Buick-3-8L-V6-Intake-Manifold-/262904934728?hash=item3d365af148:g:cc0AAOSwuLZY0a-f&vxp=mtr

Looking for grey G body rear and passenger seat upholstery. I picked up an 86 GP 2+2 with some mice damage. Looking to use as much stock parts as possible. The seat fabric on buicks, montes, and GP's look pretty much the same from 85-88. If anyone has some mismatched seats that they need to...

Been a while since I posted! Saw this on the local CL. Its like 10 miles away from me. I was super interested until I saw it had a SBC. Would been worth the engine for me if it was still carb turbo. http://fargo.craigslist.org/pts/5538653149.html If anyone wants enough parts off it I could...

A 3.8 came up for sale local and I was considering picking it up for a spare motor. Its a carbed 3.8 and 5 speed manual out of a vega supposedly. How can I ID if it is a standard 78+ high port engine externally? I am afraid if it was in front of a manual in a vega it could date it to before...

Bought a BRF trans out of a GN that got swapped out for a built one. Has an aftermarket (maybe?) converter from Precision of New Hampton. Its a D5 core. Is this just a factory rebuild? I looked on their website and dont see anything if its a stall or anything. Thanks!

Bought a BY code 200 4R that I was told good. It didnt have a converter so I bought a used D5. I put it in the car and it isnt pulling any fluid. I had the pan off and changed the filter so it was pretty much empty. Fluid and filter were nice and clean. I put maybe 4-5 quarts in and the trans...

I know its a buick board but theres a lot of guys going LS so I thought id try here before I sell it LS1tech or whatever. Ive got a PTC lockup 10" LS1 street converter. 3400 stall, 1.85 stall ratio. Purchased for the 4l60e in my 3800 firebird but the 3800 flywheels are a lot smaller than ls1...

Im swapping the Th350 out for a BY code 2004R this summer. I dont have a computer but would like to lock up the converter. What have people used for lockup modules? Painless has a vaccum modulated kit but ive read complaints about it. It sounds like it does what I want it to do but $160 for a...