Search results

I am replacing the springs on my GN with Moog 5638/5413's. There was a thread here that I looked for but cannot find again asking if the springs can be replaced with the weight of the car and a floor jack, or do I need to use a spring compressor? I am anxious to get this thing sitting level...

Has anyone *successfully* found a way to seperate the vanity mirror lid to replace the fabric on the outer side? I had the visors recovered, and have spare material, but understand the plastic was "welded" as opposed to glued, making disassembly difficult, if not impossible, to say the least...

My GN has a sagging RF spring, about 1.25 " lower than the LF. The car only has 68k miles, but thought it would be a good time to j replace ball joints, upper/lower control arm bushings, springs and steering components. I figure I have to disassemble to some extent anyway, why not replace 24...

I purchased a PowerLogger about a year ago, but for a number of reasons, have not had the time to install. Now that I have a garage and some time, I am slowly working the install. I have a basically stock setup, (see sig) and would like to know if I can install without a wideband and EGT...

I am moving from the northern Virginia area after 38 years to the Huntsville, AL area within the next month and a half. Does anyone know of any cruise nights that way?

Thinking of purchasing a 05 Chevy Silverado uramax/Allison combo. Not knowing an awful lot (read:little) about diesels, what should I look for? The one I am considering has 72k miles, going to look Saturday. Thanks!

I am not sure where to post this... I am looking for comments, good and bad and or personal experience with 4 wheel steering on a 2003 GMC Denali Pickup with around 112k miles.I am thinking of buying one, but know little about the system Depending on the feedback or comments, is there anyone in...

Just checking... The VSS input can be found on the ECM at pin A10, correct? This is the smaller (24 vs: 32 pin) connector, correct? Thanks!

I just purchased a PowerLogger... arer there any tips/suggestions anyone has learned in the installation process? Pretty straight forward, but I thought someone might have a suggestion or two. Thanks!

Please delete, thanks!

I am building a GNX dash using the VDO Vision series gauges (tach is # 333-155). My first test using Casper's wiring harness, the tach did not function. The tach is wired using the same (white) connector from the former tach/boost wiring harness. Do I need to wire this directly to the unused...

I am converting my 87 to a GNX dash and am in the process of removing the stock IP cluster... the only remaining task is to remove the tach/boost wiring. Is this clamped somewhere? I can't "feel" the connection from underneath. Can I tug on the harness some more to bring it to a point I can...

After reading all the horror stories of people getting ripped off I am happy to post GOOD WORDS for a change. I was looking for some small pieces of wiring, UnderdogGN had them and said I could have it for the cost of shipping! When it arrived, it was a virtually complete dash harness, of...

I am looking to purchase a set of quality GNX style fender vents. I already have the reproduction under hood ducting, and was looking for recommendations as to vendors... and anyone's opinions, experiences, etc. Thanks!

I cannot get to my PM's... I get the message below: Not Found The requested document was not found on this server. Web Server at turbobuick.com Any idea's?

Does anyone have a chunk (18" or so) of the factory wiring harness that plugs into the standard analog cluster for an 86-87 GN? I am in the process of building a GNX dash and would like to use the factory wiring and color codes on the project. Thanks!

Just a general question... I have a TE44 and the compressor housing is marked AR .60. Most I have seen or heard about are .63 what is the difference, and what is desireable, or makes it desireable? Always learning here! Thanks

Does anyone know the part number for a 87 GN G80 pinion shaft bolt? Thanks in advance!

Does my 87 gn use c-clips to retain the rear axle? I just found an axle seal leaking and will replace both. I am familiar with the older GM 12 bolt units and just want to see if this is similar. thanks!

I have a Razor's kit in my GN. It is infrequently driven, shows, cruzin, fair weather, etc. How long will the meth retain it's "potency" or whatever you would call it? Thanks!