Search results

  1. Tim Cucci

    Stock Rebuild LC2 Flexplate questions ?

    Hensleyt thanks I posted this photo before I saw your reply. Thanks for the confirmation. I was thinking not to balance and that would absolutely solve the flexplate issue. Like I said it’s a stock setup all original except the 10/10 crank that I already have. Not looking at Race type...
  2. Tim Cucci

    Stock Rebuild LC2 Flexplate questions ?

    Flywheel in question for stock rebuild and balancing can this be used .
  3. Tim Cucci

    Stock Rebuild LC2 Flexplate questions ?

    I have a spare original engine that I would like to put back together. A 10/10 GM Turbo crank to be used with stock bore pistons and rods and block. All are original to the block. Only thing new or different is the stock turbo 10/10 crank and bearings. #1 Has the rotating assembly absolutely...
  4. Tim Cucci

    Popping at idle and running rough after battery swap??

    SM read 13.6V ?? It’s kinda freaky huh? The new battery is a size 78 and not the smaller 75. 800 cca instead of 650cca?? Gremlin?? Maybe??
  5. Tim Cucci

    Popping at idle and running rough after battery swap??

    New Battery is going back to guess where?. Getting the $$$ back too. Wal Mart. I had a old woman that fixed weed eater ‘s tell me “ ya buy sheet ya get sheet”
  6. Tim Cucci

    Popping at idle and running rough after battery swap??

    Well this is nuts??? I put the old battery back in and the car runs fine!! Crazy sheet! IDK!
  7. Tim Cucci

    Popping at idle and running rough after battery swap??

    My car was running perfect. My battery was 5 yrs old and going dead after about a week. I installed a new battery and did not crank the car until the next day due to running late for appointments. I actually heard a pop in the exhaust when cranking the car and the idle was all over the place up...
  8. Tim Cucci

    Tip and stumble at at stop and go. Red lights , Stop sign. Normal driving.

    I think I got it! Ouch! I’ve done cam sensors many times! Some how, some way, the cam sensor was 180 out! Dot on gear and green dot were pointing at driver side instead of passenger side at 25* past TDC. I pulled it out and reinstalled it correctly and the car runs GREAT! No more stumble! Oh...
  9. Tim Cucci

    Tip and stumble at at stop and go. Red lights , Stop sign. Normal driving.

    Very slight stumble when leaving a dead stop during normal driving. Other than that the car idles, responds, hauls a$$, smokes the tires. I have not checked the sparkplugs yet? The car has cut out and popped at WOT like it ovverreved and didn’t shift out of 2nd quick enough? Slight Stumble is...
  10. Tim Cucci

    Want to add a Innovate WB O2 Controller Kit? Can my SM G be used for the gauge?? Problems?

    Oh and other equipment suggestions please. Not stuck on the innovate. Powerlogger??
  11. Tim Cucci

    Want to add a Innovate WB O2 Controller Kit? Can my SM G be used for the gauge?? Problems?

    Looking at the Innovate 3884 or 3887 controller kit? I’m trying to avoid adding another gauge in the car? I’ve got a Scanmaster G and TT chip already. It looks like I can just use the SM G for the read out maybe. Is this as simple as wiring from the controller to the Scanmaster and then tuning...
  12. Tim Cucci

    Scanmaster G Dim Display

    Same here Bob. I’ll get an email to ya.
  13. Tim Cucci

    PCV plumbing?

    I put all vacuum hookups in the rear of the intake while the intake was removed during a rebuild of course. It really cleans things up and vacuum is great. I did put a small breather on top of my PCV with no vacuum but I didn't like that set up. I have since ran a 3/8 hose from the large 3/8...
  14. Tim Cucci

    WTB Stainless Crossover Pipe for STOCK Headers

    Sent you a message
  15. Tim Cucci

    Size of oail cooler adapter ports

    1/2" NPT is the size and type that thread directly into the oil adapter. 1/2" pipe. I just replaced mine with 7/16 ID hose and 8AN fittings. I used a 45 degree fitting on one of the lines at the oil cooler and it leaked. I replaced it with a straight fitting and it's OK. I really am disappointed...
  16. Tim Cucci

    Need help with OLD SMC Alky Connectors on top of bottle.

    Round bottle with two RCA type connectors. One male and one female. All my RCA type connectors are made with only one wire molded in the connector. The old SMC connector actually has two conductors going into one non molded RCA type connector. Two conductors to one male RCA. Two conductors...
  17. Tim Cucci

    Need help with OLD SMC Alky Connectors on top of bottle.

    can someone identify what the connector types are on the old SMC system bottle. My system works well but the black plastic insulating nut has crumbled on both wires going to the top of the bottle. I just need to get new ends for the cables.
  18. Tim Cucci

    WTB Stainless Crossover Pipe for STOCK Headers

    Thank You Very Much for that advice. You just saved me some bucks and some efficiency. Got any tips on sealing the stocker real good? I do appreciate keeping things simple and not just pouring money and parts at something that's not practical for our driver cars. I just want a quiet, smooth...
Top