Search results

Item SOLD!! I snagged a GN1 SPAL set-up a while ago, and I thought I'd pass along my 2004 Dodge Intrepid dual fan set-up (also known as Ramchargers fan for you vintage members ...) that I took out. It was operating just fine, and I cleaned it up a bit. The shroud in not cracked or broken...

SOLD!! I have a nice used set of ARP head studs for cast iron heads for sale. I believe they have only been loaded once, and are ARP part number 123-4203. They are the black oxide, 12-pt nut kit. They are clean and in very good condition, and will come loose without the ARP install instructions...

I recently decided to change my Grand National front end over to coil-overs, so I thought I'd post these parts I took out ... I have a set of Global West lower control arms for coil springs (Part number CTA-37L I think), a set of Detroit Speed front coil drop springs, 575 lb/in rate (DSE part...

I bought one of the larger oil vapor separator kits from SS/GN here on the Forum a while back, and I thought I'd pass along the set-up I replaced ... It is built around one of JLT's (Now J&L Oil Separator Co) billet black anodized 3 oz reservoirs with two 90-degree Push-lock fittings, and has...

Item CLAIMED!! I replaced this Rochester evaporative fuel vapor canister on my '87 GN with a NOS one, so I no longer need this one ... It has 100,000+ miles on it, but it doesn't cause any issues on my smog tests, and doesn't smell gassy ... I'm pretty sure the solenoid works as well, although I...

SOLD!! When I replaced my motor last year, I sprung for a new set of radiator and coolant hoses to start off new again. I thought I'd pass along this good set of silicone hoses that I took off my car during the rebuild. The upper and lower radiator hoses, the s-hose, the front heater coolant...

SOLD!! Swapped out my OEM-sized vacuum brake booster for a larger Caprice model, so I'm passing along this nice unit I took off. It's the OEM size (9-1/2" ?) dual-diaphragm model that is correct for G-Body cars. I had it replated/rebuilt before I put it on a couple of years ago. I clear coated...

Up for sale here is a nice used Hellwig rear sway bar, the trick one that has three different stiffness settings. Part number 55809. The bar is complete with all the fasteners and parts, the install instructions etc. The bar is in nice condition with a gray hammertone finish, has no broken parts...

For Sale: I just redid my motor again, and put a new alternator from Kirban in the car. I rebuilt the old one, and thought I'd pass it along. All new internals (rectifier, regulator, brushes, brgs, batt post etc), correct 120A rotor. Case was powder-coated silver and then clear -coated. The...

Up for sale is a nice used Buick Regal instrument cluster surround or dash surround. I was going to use this one in my Turbo Regal rebuild, but I moved in another direction, so am passing along this part. It is in good overall condition with no holes, tears, dings or broken mounting tabs. The...

My crank-mounted IC fan has hit my IC a few too many times ... Anyone got a nice one that they no longer need? If so, PM me pics and shipped price to zip code 94582 ... Thanks in advance, John Alvarez, Turbohh

For sale here is a really nice original G-Body hood release latch mechanism and mounting bracket. The mounting bracket has been cleaned, primed with with self-etching primer, and recoated in SEM Trim Black for that nice GM satin black underhood color, and the latch mechanism has been carefully...

Hi! Does anyone have the funky pre-86(?) driver side power seat switch mounting bezel/housing/escutcheoon thingy shown below, but that's in good condition and not dried out and cracked/broken etc? I didn't see a GM part number molded in this part anywhere. Or does anyone know if these are...

I got worried about driving around Ca with an obvious test pipe in place of my cat, so I had a pipe made that looks more like a cat. I'm passing along this test pipe that I had custom made to match the oval inlet to the Pypes cat-back exhaust I have on my car. The pipe is 3" diameter, and is 13"...

I bought a set of genuine GM outside dew sweeps for my '87 GN back in 2009, and tucked them away so safely I couldn't find them until just now, after I looked and looked and gave up. I no longer need them now (of course), so they are up for sale. I paid just over $150 for them from a GM dealer...

Up for sale are a couple of sets of original GM parts off my '87 GN: I put new upper door panels in the front and rear, and thought I'd pass these originals along. They are for manual non-power windows, are in good condition with no rips, tears, or serious stains. There is some degree of...

I redid the front and rear of my '87 GN with SpoolFool fillers, and thought I'd pass along these Danko's that I took off. They are painted black, and are in pretty good shape ... There are no cracks or major damage to them, and they are clean. The biggest flaws are the rub divots that the top...

I thought someone could use this upper dash speaker cover ... It's in good condition other than it has a small crack near the driver side radio grill, and its got the usual warpage in the center and at the ends by the B pillars. Also, the windshield beveled edge has black windshield sealant...

I have swapped over to a different turbo, and no longer need this one. It is a Precision 6766 dual ball-bearing turbo that has about 2500 mi on it since I sent it to Reed Patridge at Work Turbo for a refresh. This turbo has the CEA billet wheel, a ball-bearing center section, a 3-bolt 0.63 A/R...

Can't say enough good things about Brian and his company, G-Body Parts. Brian has gone way out of his way to help me obtain a custom set of front and rear seat covers for my Lear Siegler seat install in my '87 Grand National. Brian even offered to help me sort out the pile of rusty power seat...