Search results

Looking for a pair of bucket seats for my GN. Condition of the covers not important. Looking for useable frames and foam. Need to be complete with grey trim pcs. Will pay for nice ones too. Closer to northern Indiana the better. Thanks.

This is a panel I fabricated for my GN. It holds an ls computer securely in place. It is made out of 6061 aluminum, .090" thick. The cover is held in place with 6mm screws, into threaded rivet nuts. Powder coated black. Foam seal already glued on back. Only selling cause I switched to Holley...

This is a panel I fabricated for my GN. It holds an ls computer securely in place. It is made out of 6061 aluminum, .090" thick. The cover is held in place with 6mm screws, into threaded rivet nuts. Powder coated black. Foam seal already glued on back. Only selling cause I switched to Holley...

I have a 5.7 ls motor with a t76 turbo. Just got the first tune for 6psi, and was putting some miles on it. About every other time I would get into boost, it would start smoking. Bad. Like, inspector gadget, smokescreen bad. Drove for about a half hour, and had about 3-4 ounces of oil in my...

Ok, this may sound like a dumb question. My ls swap has corvette brackets and pulley setup. When I was gathering parts , I noticed that a stock vette ps pump looks identical to the stock buick v6 pump. Sure enough, all the holes lined up, and I pressed a vette pulley on it. Just got the car...

Well this may come towards the end of this build, but so much had to be tweaked along the way. Purists already don't like this none too much, but this car isn't an original, numbers matching car to begin with. My goal is low tens with this car, and hopefully I have the ability to get there.

What's up fellas. I am currently having machine work done on a 2001 5.7 alum. block. already ordered srp pistons and eagle rods. c.r. will be 9.0 to 1. my car has a decent 3.8 with a t63e precision turbo in it now. I am running 50lb. injectors. Can I , or is it worth it to , buy two more...

Here are some pics of stuff I built for my car. This was my first frame off, and I am happy to be nearly completed. I fabbed the intercooler tubes, intake tube ( you can't see the k&n under fender ). I also built the cage and dash panel.

I have the intercooler, both pipes, but only two 3" to 3" coupler hoses, 2 3" s.s. clamps. I'm using the other hoses. I bought it brand new for$989.00 Looking for 650.00

I have a turbo 350 that is 9 sec. ready in my car now. it has a full manual valve body in it. Is it possible to make it shift "normal" in a car that makes no vacuum when in the throttle? Didn't want to waste my time if it won't work.

Will a gn run with the cam sensor 180 degrees off? if so, would it idle ? also, will it run with a bad crank sensor ? When they go bad, do they just stop working altogether, or will they screw up timing enough to cause detonation.?

I will try to tell this the best i can. I had an 86 t-type with rebuilt motor. at that time i added the following. JE pistons and rings,precision cam, t63e turbo, 50lb. inj., precision fmic, walbro 340 fuel pump. Still had stock maf. Ran a 12.8 at 106mph. Not nearly as good as I expected...

Precision fmic- both pipes-two 3" to 3" hoses- no clamps- used for 1000 miles. A little dusty, but openings have been taped off since removal. $750.00 or make offer original 86/87 intercooler. decent shape. with both side brackets. $150.00 stock injectors-(6)- $30.00 86/87 air cleaner...

Has anyone ever mated a gn engine with a 5-speed trans. This may sound weird, but I own a 79 porsche 928, 5-speed. The car only has 49,000 original miles, and it is a blast to drive. But mostly in the twisties. The problem is that it has absolutely no balls! A gn engine would shave approximately...

Last week I finally was ready to take car for it's maiden voyage. (or so I thought) First of all, this car was a frame off resto. Motor is from my 86 t-type. Engine ran before just fine. Anyways, the car was running fine in the garage. Started, idled, and was in driveway ready to go. With no...

Has anybody used the hotchkis 4 piece spring kit # 1902 ? Will the front springs lower the front from stock ride height? I think this is a universal g-body kit, and most came with v-8 engines, which should be heavier than a g/n engine. I already have the springs installed but the engine won't be...

I had these polished about 1 1/2 months ago. Centers re-finished in satin black.Never had any bends or curb rash, $900 obo Will send pics upon request. They are non-dimpled. Thanks Chris