Search results

I'm looking for the bolt/stud that is mounts the belt tensioner/ac compressor I believe it mounts to the accessory bracket that everything bolts too. Thanks! Rob

Well, this is my 3rd Walbro pump since 2007 that has failed on me. This last one was the free replacement pump that was supposed to have all the bugs fixed out. Well, I don't really want to stick another Walbro in my tank and i'm kinda lost on what I should put back in there. I have used the...

Hey Everyone, I had a problem develop last year where I would get a stumble at around 2000 rpms when the car got heat soaked. The car ran great cold or if you were going 55 mph down the road. If I got in stop in go traffic/ slow speeds or let the car sit after running, the car would act up...

My car started doing this earlier this spring. When I get in traffic, or park it when the engines hot, the car will start bucking/stumbling right when you start to push in the throttle. As soon as you push it down more, it clears up and runs great. Once you start moving and the car cools off...

I am buying my first house and I am starting to clean stuff out of my dad’s barn. I bought an intercooled motor back in 2008 and I converted my car over. My plan was to hold on to this motor, but I don’t see myself ever using it again. It is a 1985 20-bolt motor with around 125k. The motor...

I purchased a complete intercooled motor back and 2008, in which I rebuilt and put into my car. My hot air motor is just sitting in the barn and i'm thinking about selling it. Whats a hot air motor worth with everything minus the injectors? The motor ran alright before I tore it out, but I...

Chris, I did not use the line bias spring in your shift kit due to the instructions saying that if my car was over 300 horsepower, do not use it. Could this be related to my early shift points? I have been told that this spring is usually changed out. Thanks, Rob

I was looking at my collection of pictures today and I still can't believe how much work I put into this car. And i'm still not done! :)

I have done a search, but I want someones opinion on my situation. My car used to shift alot higher before I installed a CK Performance shift kit, but now it shifts around 4000 RPMS at WOT. Part throttle shifts are great. Would shimming the throttle valve limit spring be the best route to...

15x7" 3.5 backspace. Thanks! Rob

The last time I went to the strip, I fill up with 110 octane and drove the 30+ miles with 16 psi of boost with my turbo tweak street chip. After awhile, It seemed as if my car was pulling alot harder even though I did not increase the boost yet. Am I crazy or does the fuel help at that PSI...

The last time I went was back in May, ran a 13.7 @ 103 mph. I added drag radials and a full tank of 110 octane and ran this yesterday. 60 ft 2.063 1/8 mile 8.598 1/8 mph 86.30 1/4 mile 13.280 1/4 mph 103.23 This was my best pass and I ran 20 psi of boost, 0 knock, 02 read 780 at the...

Hey guys, Need some input here. My blower motor stays on when I turn the car off? :confused: Blower control module? Rob

I was just about to install my free replacement f-169 pump until... I dropped it.. poop.. :o Thank goodness I didn't have the tank out of the car yet!

I have the Concert Sound II system in my car and I blew the tweeter in my drivers door. Is this just a 3” speaker, or a tweeter? I have not had my door panel off to see exactly what it is. Would a 3” aftermarket speaker fit in its place? Does anyone know where I could locate an OEM speaker...

60ft- 2.25 1/8th- 8.99 I was running 16 PSI. Does this sound about right?

I searched with no luck. Can someone show me pictures of the trash can modification for our stock intercoolers? Rob

Edelbrock double timing chain. I bought a 86-87 motor and this was on it. Suppose to have 10k miles on it. $15 + shipping Coyles standard replacement timing chain set. Never used. Came with my rebuild kit, but I went with a new double roller. $20 + shipping Inlet bell $10 +...

Anybody have any of these? :cool:

I decided to put in a CK performance shift kit in my trans because I wanted it to shift firmer. I just had the trans rebuilt last spring and also had a super servo put in it. It shifted great with the old hot air motor, but it kind of turned mushy at WOT with the new intercooled motor. It...