Search results

My engine ran very rich with lots of missing then quit. Replaced coil pack and ignition module, ECM, plugs and plug wires. Casper's CCCI sensor check says its the crank sensor. I installed a new crank sensor, still shows a problem with the crank sensor. Car had not run in a few years. All...

Nice 87 T-Top Excellent interior Steel GN Wheels 2 8x15 and 2 10x15 Coil over shocks front and rear Tubular upper and lower control arms Adjustable Rear Upper Control Arms Ford 9 inch with Nodular Iron center and trac loc SPOHN Pro series Rear Anti-Roll drag sway bar 4 wheel Disc brakes w/E...

We had 12 GN's this year. Yes the white one is a real GN,

Wonder what happened to the new Grand National? http://www.msn.com/en-us/autos/detroit/400-hp-buick-avista-concept-debuts-ahead-of-detroit-show/ar-CCn3qz?li=BBnb7Kz Sits on the Camaro platform. Guess the dropped the idea of bringing back the GN and GNX

Looking to buy a stock air filter box for my 89 TTA. Thx

Ordered a "New" gear from Ebay and Here's what I got.

New disc brake mounting kit w/e-brake calipers and used 11.25 inch rotors. The rotors are in very good condition. The mounting kit and calipers were installed but never used (I discovered after installation that my 15 inch steel wheels would not fit) This setup will not work with 15 inch wheels...

School principal and Iraq vet has sent a message. http://www.foxnews.com/us/2015/02/26/principal-logs-on-to-twitter-to-take-on-cyberbullies-says-theyre-worse-than/

Ford 9 inch w/disc brake conversion - Yukon Nodular Iron Pro N-Case w/ 5/8" Cap Bolts - Aluminium Daytona Pinion Support - 1350 Billet Steel Yoke - 28 Spline - Ford Motorsports Trac-Lock Posi Unit - 31 Spline - Motive Performance Gears (3.70 Ratio) - Timken USA Bearings

Accidentally shut a bird up in my garage with the GN. Three times on the hood and once on the trunk lid before the ..... croaked.

I hate those kind of threads where the answer can be calculated but. In this case I calculated the Ratio and I'm not too comfortable with my answer considering the cost involved. I have a 3:42 original rear in the car but I've added 275/65 15 Drag Radials (28" tall). I have a Ford 9" housing...

Some parts I've outgrown: MSD 50's and street chip $150 TA49 no play (2) $475 ea Single pod Pillar gauge holder $30 Dual pod Pillar gauge holder $35 Used set of Ebay headers $140 (Pickup only) Added B2B ECU see post #23 All prices are shipped to continental U.S.

:bored: Actually its not that bad, I decided to relocate some gauges and install a knock gauge while I was doing the Alky install. Looks worse than it is.

Installing an Alky Control kit but I can't seem to find a grommet in the firewall behind the coil. I've had the engine out a couple of times and I don't recall seeing one. Am I missing something?

I have a 2 wire connector I found while replacing the MAP sensor. It is "L" shaped and has a black wire and a white/black wire. I can usually figure these out but this one has me stumped. Any help would be appreciated.

See the Cruisin The Coast post in the Regional Forum Southeastern Area.

Cruisin' The Coast is 5 to 12 October. I'm just checking to see if there is any interest... I have a 3 bedroom "mancave" about 150 yards off the beach in Gulfport. It's equipped with a 2 post lift and sleeps 4 (or 6 if you bring your own sleeping bag) with plenty of parking. Any TR owners from...

1979 Malibu 454 Big Block Oval Port Heads 9.7:1 Compression Ratio 3 angle valve job Crane Hydraulic Cam, lifters, valve springs Cloyes true-roller timing chain Edelbrock aluminum intake manifold Edelbrock “Thunder Series” 800 CFM Carb or Holley 750 CFM HP Mallory Distributor MSD 6Al ignition...

Ends today!