Search results

Like the title says I'm looking for original water temp and oil pressure gauges for a GNX. Dead or alive and not in perfect condition is ok too. MUST BE OEM GNX pieces (with oil psi and water temp symbols on the face) not just replacement Stewart Warner gauges. Thanks.

Looking for a set of GNX inner fender duct pieces like the ones pictured. Let me know if you have a set for sale or know where I could get some. Thanks.

I recently had to change out the forward drum in my transmission with a billet one my stock one broke. While I was in there I was advised to do the 3/2 control valve update for my older CK shift kit witch I did and the only other change I did was installing a bigger boost valve in the pump...

Just listed my T-type for sale and figured I would put it here also http://www.turbobuick.com/forums/threads/1986-white-buick-regal-t-type-12000-in-south-florida.407113/

SOLD SOLD SOLD SOLD 1986 Buick Regal T-type 3.8 SFI Turbo V6 just like the Grand Nationals. Very clean Florida car, runs great, looks awsome and gets compliments every time I take it out. I am the third owner and have had the car since 2007. This car is almost totaly stock, the only...

Well I have been searching for days and can't seem to find the answer I'm looking for. I am looking for a visual comparison of how different brand AFTERMARKET weather strippings fit. Can someone please post pics of the fit at front and back molded ends of the upper and lower door seals and...

Well my POS powermaster is acting up again and I'm tiered of the press and pray the brakes work so I am looking for a TTA style vacuum block with the extra port for vacuum brakes.

Like the title says I'm looking for a 2.5" Y-pipe or catback in either Broward, palm Beach or Miami. I know I could get it new and I might if I cant find anything used but I just think it would be a waste since I will be cuting it up and will probably change the mufflers out to make it the way...

Selling my stash of clear front bumper parking lights. All are in good to fair condition ***not new*** please keep in mind that these are over 25 years old. I have 4 sets of right and left. looking for $30.00 a set or $100 for all 4 sets.

I am in the process of rebuilding my transmission and am pressure testing all the components with air before assembly. Everything checks out except when I test the overrun clutch assembly, there is air coming out from the back of the input shaft and it seems like the air comes through around the...

OTC 2000 , Works perfect, comes with GM up to 87 and a Dodge chips Also comes with Instructions and all hardware needed to operate. Have no use it anymore since I have a powerloger . $70.00 shipped

Just wondering if anyone here can answer a question as to what the SG1 casting on the side of a 109 block means:confused: Are these blocks any better or worse than the typical block found in turbo Buicks. The main caps are a little different as they have some ribs on the sides to identify #2...

Looking for gray upper door panels and front bucket seat upholstery for my T-type. I am switching from the factory nasty burgandy that came in the car to gray and have everything else but these pieces. I am almost ready to just buy new but would like to see if I can save a few bucks on...

I need a vacuum block that goes on top of the throttle body with the extra port for vacuum brakes. Let me know what you have Thanks Denis

Selling a pair of 2.5" ATR stainless steel mufflers I had on my car for no more than 1,000 miles. These mufflers are like brand new with no damage what so ever and I even still have the original boxes they came in. They were installed using band clamps so there are no crushed clamp marks so they...

In need of a panhard bar and stiffhard bar for a GNX suspension (the two bars that go across the back). Any help would be appreciated. Thanks

Finally found the source of my noise and vibration at higher speeds:D I going to change all the bearings in the rear and was wondering what fluid you guys would recomend and does it require posi additive because the crap I used before obviously was not working :rolleyes:

I have to rebuild the rear in my car because its making noise:mad: and think my axles might be bad so I am wondering if anyone knows if the axle shafts in the 7.5" diff in a regular Regal are the same as the ones in a GN:confused:

Can I just go to a junk yard and pull any 3" or 3.5" newer style GM mass air sensor to use with a translator or does in need to be from specific cars or trucks? Thanks

The stock mass air sensor on one of my cars took a crap on me:mad: seems like its going around:rolleyes: so I got a great deal on a GEN2 translator and want to use a newer LT1 or LS1 sensor. I kind of want to use a 3" LT1 sensor for now so I can re use my filter and hose on my mass air pipe...