Search results

Hello,I have a couple of parts I won't be using anymore. 1.modded ECM for low impedance injectors $215 shipped SOLD 2.83lb injectors $225 shipped 3.Trans pro chip for 83lb injectors $65 shipped 4.30lb injectors w/ matching TT 5.6 chip $175 shipped SOLD 5. engine torque strap $30 shipped...

Hello, I'm looking for a stainless 3' dump pipe. Please let me know what you have please send price and pics to bigp1975@ymail.com Thanks Pernell

Hello, I'm looking for a 3'' stainless dump pipe please let me know what you have and how much. bigp1975@ymail.com Thanks Pernell

Hello, I have a atr rear bar I would like $150 plus the ride. In the lower 48 states. bigp1975@ymail.com Thanks Pernell

Im looking for a 3" test / dump pipe. Please let me know what you have and how much. Send pics to bigp1975@ymail.com or post in the thread or pm me. I'm in Oh 44121 so you can figure out shipping.. Thanks Pernell

Hello, Im looking for a rear sway bar .. Im located in Cleveland Oh,44121 Please let me know what you have... Thanks Pernell

Hello, I want to paint my tank silver, to guys who have done it what kind of paint did you use? Also what steps did you take to prep it? Thanks

Hello, I want to paint my tank silver, to guys who have done it what kind of paint did you use? Also what steps did you take to prep it? Thanks

Hello, I am in the process of polishing lips on my wheels. What is the best way to remove the factory ridges that show after you strip the clearcoat off ? Any tips would be greatly appreciated. Thanks

Hello, I have the trans pro on my car, it's been in the shop all winter. I went to start the car up to let it run last week and move it around and the engine light is blinking. What would cause this to happen. Speed density mode no maf with alky chip. Thanks

I need to replace my starter, I am thinking about using a lt1 starter since its smaller. How many guys are running them and have you had any issues. Thanks Pernell

I need to buy tires. I have for fronts and i would like to run a 245 or a 255 on the front but on the rear i would like a 295-50-16 or a 315-45 16 i want to fill up the rear wheel well with out rubbing. Can you guys give me you opinion on these sizes? Pics from the side and rear would help to...

I have a leak at the timing cover it seams to coming from the dowel pin on the driverside. I there i easy way to fix this? I have oil leaking from there and i want to take care of it. Thanks

Hey guys i need help.. I can't get the GN to start. I cranks but it wont start. I have checked the following. 1.coil packs the readings were good. 2.I checked to see if i had spark thats there. 3.I have injector pulse. 4. I have set the cam sensor 3 times and swaped it out with a known...

I need a 3-1/2 inch dump for something im working on. please let me know what you have with pics and price shipped to OH,44121 Thanks

I have a laptop stand i bought off a board member a while back. I'm not going to use it i would like $120 shipped in the lower 48, and if using paypal please add 3% . Pm me for pics and i can email them. Thanks Pernell

Hey guys i need to know what size nuts are needed for the fronts shocks. I cant find the ones that i had. Thanks

I want to put a bung in my up pipe for my iat sensor. What size bung do i need and where can i buy it? Thanks

I needed to know if the mounts are sloted ? I can't remember. My downpipe is a little tight after the install of the mounts a can't get it to clear the stock header. It's hiting on the bottom where the crossover flang is and i didn't have that problem before. I wanted to know if it's possible...

Hello, I'm getting ready to tackle my body bushings. I wanted to know if anyone that has done this project noticed more clearance under the hood, say around the downpipe and passenger side valve cover? I have a 3'' Terry H downpipe and it's a pain in the @$$ getting the pipe in and out and i was...