Search results

  1. Roy L.

    Hotchkis rear upper control arms

    Still available? I'm interested in them.
  2. Roy L.

    I'm interested in your 3 pod gauge pillar holder. what would shipping be to 44231 and how do...

    I'm interested in your 3 pod gauge pillar holder. what would shipping be to 44231 and how do you accept payment? Do you take PayPal? Thanks, Roy
  3. Roy L.

    Buick Race this Sat. 9-2-23 1/4 mile track

    Hope to see a few of you guys and gals out at Kuhnle Motorsports Park on September 2nd. We will have one for sure but maybe 2 race classes for our Buicks. If we have enough, we will be running a Quick 8 and then a regular bracket class. Both will be on a sportsman tree and both classes will be...
  4. Roy L.

    Buick day In NE. OHIO SEPT. 2ND.

    This is only a couple days away. Let's show Kuhnle we can bring the cars If given a chance and make this a bigger event in 2024. Please share and tell your friends about it. We will be having a bracket class and if we get enough cars, we will run a Quick 8 on top of the bracket class. The track...
  5. Roy L.

    Buick day In NE. OHIO SEPT. 2ND.

    Thanks for bumping this Blacky. Good reminder for all to get your car out and have some fun.
  6. Roy L.

    New pump pressure.

    interesting. mine is a new pump from Julio as well, but I could only get 180 PSI if the motor was running and my scanmaster read 14.2 volts. was your engine running when you tested your pump?
  7. Roy L.

    New pump pressure.

    You must have some good voltage running to the pump? or you got a better pump than I did?
  8. Roy L.

    120’s, 60’s w/Chip TA rear end girdle

    Turbo 6 I would like the rear cover if still available. I will be at BG Fri. Please let me know. Thanks
  9. Roy L.

    New pump pressure.

    Ok, test with key just in run postion 11.7 volts, pump test @ 140psi. Engine running 14.2 volts @ 170psi. I'm not bashing, but why would anyone sell a tester with the wrong info in the instructions? 🤷‍♂️. Just saying.....
  10. Roy L.

    New pump pressure.

    Just received another response from Alkycontrol. Older instructions. The pump should make 200 psi with 14 volts at the pump The car is off, there is a little loss of power from controller to pump voltage wise, settings within controller, etc so 140 should be about right not running. In the...
  11. Roy L.

    New pump pressure.

    Here is an email response I received back from Alkycontrol today. ( I usually get 140 at 11.5-12v on the car. At 14 volts pressure will be higher, but typically you should only need 100-120 tops ) So, with that being said I should be good, but why the instructions say it should...
  12. Roy L.

    New pump pressure.

    Oh yes you are absolutely right. I hope to give this a try here this evening or tomorrow. when I get out to the garage. I appreciate the idea.
  13. Roy L.

    New pump pressure.

    Thanks, Chuck However, the instructions that came with the tester says to only put the Key to the on position and the Alky Daul to 8. Are you thinking that I don't have enough volts with engine off to get the proper reading?
  14. Roy L.

    New pump pressure.

    So, does any have any idea why my new pump only shows 140 PSI? We kind of got off track and started discussing the new design.
  15. Roy L.

    New pump pressure.

    Correct he said cost was to high. Said the total cost with shipping would be close to the cost of a new pump. The new pump design u can buy replacement heads and do it yourself. Cost is $80 and u don't have to send in and wait for it to come back. Also u don't need 2 pumps if u were like me...
  16. Roy L.

    New pump pressure.

    The new ones have an 18-month warranty. I'm in the same boat I now have 2 of the old ones that are basically junk.
  17. Roy L.

    New pump pressure.

    I purchased a new pump from Alkycontrol along with the GN tester. New pump only shows 140 PSI. The instructions for the tester says new pump should be 170-180psi. old pumps will read 150-160PSI. why would a brand-new pump read 140psi? I emailed Alkycontrol (Julio) and got an auto reply back...
  18. Roy L.

    Oil left in pan?

    It's not a big deal, I just thought if it was a simple modification I would do it while the pan was down. Also, you can't check that oil for metal fragments if it's still in the pan. I'm going to add a magnetic plug. obviously, I'm not going to drop the pan every oil change. I just thought...
Top