Search results

I'm looking for the part number and vendor for Walbro 255 fuel pump strainer. I've seen AIrtex FS-111 and FS-30 for 340L pumps. Those number seems to be outdated not evensure if OK for 255L pumps. Any help is appreciated. I'm going to inspect my pump strainer soon and id like to be...

Wanting to buy a GN/T horn. the one closest to front burned out on me. Any available?

Looking for a PS reservoir with the side by side ports (almost looks like a Y) I already have the one with the ports stacked in top/bottom configuration. Any around?

I was thinking of doing the Ruggles Cam Bearing oil hole mods. The one where you make smaller holes and reclock the bearing. It seems to make sense and put more oil to where it is needed most. Does anyone have any experience, recommendations, downsides or know of bearings that have smaller...

Trying to launch hard on MT DRs. Blowing away at 18 psi tire press and 10psi boost. 275/60/15s How much lower can I go? Sent from my iPhone using Tapatalk

Can any one do high boost launches on MT DRs? Whats the secret? I can make 12psi boost on the foot brake but the MT DRs 275/60/15 cant hold it and get blown away. They seem to stick at about 7-8 psi launch max. 18-20 psi in tire gets same result. Am I asking too much of a DR? Times and...

Any flow or pressure benefit of running a thrust plate over a polished flat oil pump cover? I understand the plate is so you wont need to polish out the groves but I was thinking of turbulence / cavitation caused at the relief port of the stock cover. Maybe GM engineers already thought of...

what do you call the steel strut that supports the bumpers? the shock absorber looking thing

Just did a front brake job using Oreilly parts. Came out great!! Lots of good brake power even during break in. Im sure there are a lot better brake packages out there but mine were pretty bad and needed attention. So for under 200$ and an afternoons time, Im happy with the results. Heres...

I’m thinking the #2 oil feed hole is way to small on the Clevite MS-960P set. Im planning on drilling it out to match the other holes unless someone has a good reason to leave as is. See pics, compare and comment please. Gona go tighten caps and bore gage clearance now. Going to do new bearings...

I need some guidance on this odd AC clutch issue. The AC is clutch is not powered, no electric connection, however the clutch is dragging a bit and slowly turns. Not a show stopper but it sounds funny and makes a bit of dust. Is there any adjustments for the AC clutch?

I usually pass smog quite easily with a stock cat and a turbotweak smog chip. Happens this time I have a lot of VP 101 (unleaded ) in the tank. Anyone know if this would cause an issue? Sent from my iPhone using Tapatalk

Had a fantastic time at Bates once again! Thanks for all that made it happen. I got quick pics of all the cars. Here’s some of the attendees. Sent from my iPhone using Tapatalk

Recently car started pulling right and I can feel a pulsing in the steering wheel at slower speeds. Alignment was just checked and was off but now corrected and still no improvement. Could the steering box have an internal leak that makes it turn right ? Cause that’s what it feels like...

Ran some 1.6 60fts at Irwindale. Wheel cylinder rear brake up grade allowed 10-12 psi launches and the Mickey DRs stuck on the 2 passes. Actually got told I was too fast and needed a bar and jacket on the second pass. Jeremy’s car will be a beast once he gets some traction...

If you haven’t already heard 2018 just got brighter https://www.sgvtribune.com/2017/12/29/irwindale-speedway-comes-back-to-life-again/ Sent from my iPhone using Tapatalk

Finally got my line lock installed after proportion valve. Thought I would post as it was helpful when deciding where to install. It’s a Jegs solenoid. I also got the Jegs install kit that had some tube and a good amount of fittings. I used a 1/4 bender and a double flair tool. I rolled...

PM me if interested. I came across a 67kmi Ttype bench seat car. Owner is asking for proper price for a gently used car. Sent from my iPhone using Tapatalk

3 TRs running this past week at Irwindale. Anyone else want to post their vids? Heres a thread to put them in. Heres mine against a new Camaro

Anyone have a part number/ manufacturer for the solenoid to make a Jumper Valve set up? I'm looking for the Normal Closed solenoid valve to bypass proportional valve which will increase pressure to rear brakes for launches. Yeah that one. Andrew