Search results

Looking around for new lifters for the oncenter stage 2, not really wanting to run any of the used sets I have if I can find a bushed set, is that a thing? Are there any out there that are not needle bearing. Anyone carrying or making them? If not, what’s the best option? Oncenter SII, SII...

Bought this on here from 83 intercooled back in Sept for $1350 plus shipping. I recently got an XFI underseat bracket from Coach for it too. Asking $1500 shipped, insured, paypal fees covered. I never installed, it just sat here while I collect parts for the SII build. Decided to go Holley EFI...

Anyone have a dutt neck laying around? Prefer just the neck, not a complete IC because shipping would suck to Hawaii, but if price is right would consider it. Shipping to 96789 (HI) or 90220 (CA) if need be.

I have an XFI 2.0 and eDash, might be picking up a clean mostly stock 87 GN. It has the GNX cluster so has most gauges you'd normally put on the A pillar or console. I don't want to add a bunch of gauges and extra crap, want to keep it simple, but also monitor vitals. I have a fully built on...

I know there is the Norbs thread, went through all 57+ pages of it the other night, and didn’t really see anything. I know Nick M has a killer Vintage Air setup that works well, but it’s out of my price range. I have seen the ATR kidney plates, read of smaller heater cores being used. I was...

Have a GN I’d like to VIN verify if possible. Can PayPal for your time. PM me, or reply here and I’ll PM VIN. thank you in advance.

So I have a handful of control arms laying around from all the Jeeps I install lifts on, and was looking at the straight lowers thinking it’d be sweet if I could mod these to fit the GN. Car is not at my place though. Can anyone tell me the width of the end, as in where the bushing is? Or if you...

We don’t have many junk yards here on this little ~44 mile long rock in the middle of the Pacific, so hoping someone has one of these laying around. Also hope it’ll squeeze into a flat rate box? Price shipped to 96789 Mililani, HI. If that shipping is too much, can ship to my freight forwarder...

Looking for a set or two of Stage II valve covers. Need one set, preferably a nicer set for a street car, and another set can be a little uglier. ugly set is going on a beater SII engine for some local dirt drags possibly. Shipping to 90220.

Anyone have one laying around they want to get rid of? Shipping to 90220 (or 96789 Hawaii if not too horrible)

Odd question that I can't find an answer for... If I was to have a Turbo Buick on an engine test stand just to do testing, heat cycles, break in, etc, can you remove cam sensor and drop in a basic HEI distributor for even fire in its place? I want the engine stand to be pretty basic, and one...

Hey guys, I am going to try to hook up with Mike, aka Spoolfool and get a set of his bumper fillers out here for my turd. Shipping is same price if we order 2-3 sets, wanted to see if anyone else needed a set and wanted to split shipping costs. Anyone else in need?

Building up my GN, which will get its Stage II once I get the body/interior/fuel/efi stuff figured out, but in the meantime I am considering throwing together a beater, low budget NA Stage II for the local dirt drags. I think it’d be fun to throw a nasty NA BMS V6 in something, put some boggers...

Got a standard bore 109 included with a car I bought, but guy lost main caps and bolts. I know caps from another engine (factory or billet) will require machining and won’t just bolt on, but I don’t want to waste this block. Anyone recently do all 4 billet caps and want to get rid of their...

I have been out of Turbo Buicks for about 5 years now but since retiring from the Navy in May I finally picked up another GN that I am building. I have a built Stage II/ TH400 combo waiting for install, but I’ll do that later down the road. For now I will be running a 109/200R4: Ported heads &...

Picked up a hot air GN recently, but also just scored an 87 GN engine and trans, mostly complete. But they hacked the harness and down pipe. Need the harness, and would entertain an aftermarket down pipe. Anyone have anything laying around? Shipping to 96789 (Hawaii) if you can fit it in a...

Been out of Buicks for about 5 years so it kind of feels like I am having to relearn a lot as things have changed. I finally picked up a GN to build, and will be putting my Stage 2 engine in it later on. For now I will be running a 109 setup on alky and high boost, and have 120 or 160 pb/hr...

Bought a GN with 2 fronts, 2 rears, need another pair of fronts. Shipping to 90220

Sorry, been out of Buicks for about 5 years, going through a tub of parts since I finally grabbed another GN. The smaller one with the LED & button I believe is a Bob Bailey volt booster, right? What about the other? Looks like it goes inline of the TPS or MAF, and looks like the gray plug is...

Picked up an 85 GN as a rescue, and need a clean set of injectors and chip. 87 or 91 octane is fine, injector size isn’t really important at this point, just need it to run and drive while getting prepped for the Stage 2, so cheaper is better. Would even entertain a clean set of stockers. Still...