Search results

Have an early BOP 2004R and a CK separator plate. Will use a later VB. The case is not multi and not 200C. Anyone, heard of any issues? The trans was just a case when I got it. The original VB and plate is gone. Have a GN plate here too.

Like new Hughes deep pan Sat too low on lowered Trans am Mocked up - removed Will need new filter and gasket One bolt isn’t perfect. Pan is like new. No mods were done to the pan. Have the box. Cost me $250 Went back to stock as nothing fits this car. $200 shipped lower 48 sigtauswt@yahoo.com

Never used CK Deep Pan Have a sump for it. Pan was well over $300 when I got it shipped. Mock up - too low for me on a Trans Am. Sump has new filter 904 Chrysler email for more pics. Asking $225 shipped in 48 lower USA. sigtauswt@yahoo.com

Looking for a KZ valve body and governer. Need more RPM

Question, can the TH200 drum be machined to work in the 200r4 ? Can anyone machine it to take the 200r4 center support ? I know the center support from a 200r4 won't fit in the Th200 direct drum. I have a TH 200 GM drum that is like new, and would like to use it.

Looking for the instructions so we can get this kit removed ! This BQ transmission has turned into a nightmare as everything in this thing is either junk or more work to make it right. Thanks in advance

Need a good 200R4 Direct Drum w/Springs and retainer. 16 springs preferred, but right now what I have is junk and WIT sent me more junk so today is just not my day......thanks in advance.

Picked up a BQ this weekend and its was all covered in old fluid and dirt. At first, I did not think much of it. Torn it down to the case today. Looking through all the parts to put in the washer....I could not find the deflector ? This looks like why it was blowing oil. The case has very...

Just like the title says. Found a chipped / split bearing on the center support and in pan. Really bummed as was in the process of fine tuning shifts with the governor and had to pull the trans tonight to see what broke. I did pull everything out to the sun shell and all broken pieces were...

Just installed a rebuilt 200r4 with a Rebuilt kit and Ck front pump. What concerns me is the low TV pressure at idle. I did connect a pressure gauge and pressures are below, Park 65 no tv and 265 full tv Reverse 120 no tv and 265 full tv Drive is the same as park. Od is the same as park...

Looking for the metal inspection cover at the trans. Must be Buick version not the Chevy. I have a perfect metal one for Chevy that will trade or will pay with PP for the correct Buick one

Anyone have a medium weight governor laying around ? Do not need a NOS quality. Do not need the speedo gear just the govenor. Even just the primary and secondary weights with springs woud be fine if someone has pieces of one. Thanks, Mike

Have CK's kit and have both the big springs and little springs. The little springs look like servo pin springs. I tried to place these little springs under accumulator piston and hold them in place. I assume this is correct and re-read the intruction with the kit as its different than Ck'S...

Anyone have a #1 thrust washer for the input gear ring clearance that they want to part with ? I have a #2 and #3, but need the #1 it seems. Will pay via Paypal right away. thanks......

Using a billet forward piston. Do you use the wave plate or not ? I think this should be a steel on the alum piston. I also think I need to use .061 thick frictions as well. If anyone has done this before I would like the parts list and stack order. Thanks

Started my build and my piston that I need to use has no checkball. Any concerns? I used one a while ago in my other trans and it had the checkball. Just asking as this trans is going together this weekend.

Looking for a clean complete cheop AA code valve body. This is going into a retofit Big Block Olds so just need a decent VB. Thanks..,,

Guys...got a problem with my hauler 2003 Chevy 2500HD w/4L80E. After the temp goes over about 150F, I get this nasty 2-3 shift and a check engine light. GM tech tells me about TSB No. 08-07-30-001. Truck is not under warranty and has 72k miles. I pulled the pan and its clean. Fluid is...

I have a BRF 2004r that I would like to put in my 79 Trans Am. Knowing this transmission came out of GN I think I need to lower the WOT shift point. How can I do this ? I have another governor, but don't know how this will work with the valve body. I would like a governor that shifted at...

What RPM should I see the tranny shift at WOT ? BRF tranny, BR3 VB, GN governor. I want 5000rpm,