Search results

Does anyone know if the Alradco dual fan kit will fit the G-Body Parts Aluminum Radiator? http://www.gbodyparts.com/product_info.php?cPath=46_21_61&products_id=623&osCsid=84d33e9589e62a1655adb6f0c94412c9 I don't see why it wouldn't but figured I would ask. Thanks, Scott

Anyone on here planning to go tomorrow night? I am thinking about heading out and wouldn't mind meeting some of the other turbo buick owners in this area! Scott

Getting ready to convert to vacuum brakes but want to paint the vacuum booster black. I was thinking of using a scotch brite, etch priming it, and then spraying it with some trim black. What is everyone else doing with the vacuum boosters? What products are you using? Any information/feedback is...

I am looking to install the MAF Translator inside of the car in the glove box. I bought an extension harness but am not sure which is the best way to route it and bring it into the car. How has everyone ran there wiring into the car? Where did you install the translator in the car? Thanks, Scott

Does anyone know what the differences are between the TA Performance downpipe and the RJC downpipe (fitment, performance, quality, etc.)? Any information is appreciated as I am planning on ordering one soon. Thanks, Scott

I saw a Grand National at Indian Bend and Loop 101 in Scottsdale Saturday night. Does this belong to anyone on the board? Does anyone else from AZ go out here on Saturday nights? Scott

I had a hungry mouse in my trunk and it did quite a bit of damage! Does anyone know what this item is that I need to replace? Does anyone sell this? I don't know if this is the rear jute matting or something different. Any information is appreciated! Thanks, Scott

I am going to be replacing my stock MAF sensor with a LT1 sensor and translator. I currently have a TT chip. From what I read, it sounds like I do not need a re-burn but I wanted to double check on this. Any information on this is appreciated. Thanks, Scott

I have went through three ignition module/coils recently and cannot figure out what keeps causing them to fail. Each one lasts about 100 miles. The car will run fine for a few days and then it will have a serious issue with the ignition cutting in and out. Replacing the module and coil fixes...

Trying to see if the coil/module that I put on 100 miles ago is is bad already. Thanks, Scott

I have received two new GM ignition modules lately and both of them have had the same issue. One of the blue wires is too short to connect to the coil pack yet the yellow wire is too long. I was able to get one of them hooked up but it blew the fuse immediately when I tryed to start the car. The...

Does anyone know where to find replacement power steering pump bolts or the original EGR bracket? I looked for both from GM and they were said to be discontinued. Any info on either is appreciated. Thanks, Scott

I am looking for the clamp that holds the EGR in place. If anyone has one or knows of someone that does, please let me know. Thanks, Scott

Finishing up my engine rebuild and am getting ready to rebuild the oil pump. I bought the melling rebuild kit and it comes with a few different springs. Was curious as to what springs people are running. My front cover is standard and not a HV. I will be running a booster plate and my bearing...

Are new flexplate bolts still available from GM? If not, is there an aftermarket supplier for these? Thanks, Scott

Anyone know off the top of their head what fittings are needed to install an oil pressure and water temp gauge? I thought I wrote it down but I can't seem to find it. Thanks, Scott

I know that on the website it says this chip will not pass emissions. I am assuming that some of this is because the EGR is no longer functioning. Has anyone tried to pass an emissions test with this chip and what were the results? Just curious! Thanks, Scott

Should I use the stock inlet bell with this turbo? If not, what are my options? Thanks, Scott

I am looking for a stock oil pan in good condition for an 87 Grand National. If anyone has one, let me know! Thanks, Scott

Are the Comp Cam 980 springs the correct springs to go with with 206/206 hydraulic flat tappet? I looked on Comps site and I only saw a 206/206 hydraulic roller. The only hydraulic flat tappet listed was a 212/212 and the 980's were the springs for that. Thanks, Scott