Search results

  1. S

    1 1/2" spacer for Champion racing int. manifold

    Looking for one in good shape(like new). Let me know what you have and price. Thanks, Tom
  2. S

    Garage Sale - 3" DP, Tubular UCA, B Spindles and more

    Where's local p/u? Interested in spindles. Am I correct in thinking that they are off a blazer?
  3. S

    1/2 " Plenum Spacer

    I'll PM you so we don't hi-jack the OP's post.
  4. S

    1/2 " Plenum Spacer

    I had no problems w/the 1/2" spacer on the 86 gn, but I had the old motor mts. It was actually ~5/8" w/the addition of the rjc plate and gaskets. I purchased a 1" spacer for my champion int. on the 87, but I 'm considering going to the 1 1/2" spacer and a Hartline hood. I have H&R motor mts...
  5. S

    Internals for different power bands question

    Look into the MSBC-1, boost controller as suggested by rag231. I believe it will more than serve your needs w/all it's separate ramping capabilities and combined w/better wt. transfer for god traction control. The price should be reasonable now also. look for the later model.
  6. S

    High Compression VS Low Compression Opinions

    Definitely not a pig, that is at the 21#s of boost for street duty. It was just a little lazy w/o the turbo kicking in.
  7. S

    High Compression VS Low Compression Opinions

    Subscribed: For what it's worth, the compression on the previous build was ~ 7.68:1. w/Cal tuning to 610 whp. w/a 71GTQ. The new build is w/9.5:1,that will need to be tested. The old combo was mild mannered until you engaged the turbo. Looking for better response on the low end w/the higher cr...
  8. S

    RIP Charlie Frierson

    Thanks for always being there for the community and the individual, alike. W/knowledge, passion and guidance you have helped to create a good path to follow in spurring ourselves and fellow members to making our community better for all who enter. Though we will sorrow and miss you along w/your...
  9. S

    Borg Warner turbo in a Turbo Buick!

    I think this new technology is great and that the 4-bolt should have replaced the 3-bolt years ago. However, how are these new 4-bolts going to effect the racing rules? Aren't most of the classes required to use 3-bolt?
  10. S

    Sound deadening trunk

    Some where in the archives is an old discussion about the drone that was driving everyone batty. What I can remember from it was the purpose of the factory designed exhaust was to eliminate the drone. Which doesn't show up until we went from the stock to aftermarket. I went to a 3" exhaust and...
  11. S

    1/2 " Plenum Spacer

    Fullthrottlespeed and Cruz both sell them, but Cruz may have his own logo on his.
  12. S

    Sound deadening

    I don't think it could hurt anything as long as it doesn't cause any condensation build up or stop up the drain/weep holes at the bottom of the doors!?
  13. S

    Run Data, Turbo ?

    Try to list all your known mod's in your sig so as to reduce the amount of assumptions on our part and it will lead to better educated guesses for you. Also check for too much play on the w/g rod adjustment. Should be none.
  14. S

    Cylinder head install

    Don't forget the thread sealer, arp or other and minimize the build up on the top of the deck to prevent an overage from getting between the surfaces and gaskets. Can lead to early failure.
  15. S

    Razors Alky kit (complete)

    pm sent.
  16. S

    Razors Alky kit (complete)

    Do you take P/P?
  17. S

    Razors Alky kit (complete)

    Is this the progressive single or dual nozzle kit?
  18. S

    Need a picture

    Only if you have to trace out the wires, you have to undo them.
  19. S

    Need a picture

    I have added terminal boards to take control of the increase in wire connections then bundled the wires w/cable ties or flex conduit. It gives the appearance of order until you're troubleshooting.
Top