Search results

Xfi 2.0 If my battery is low car will crank but check engine light will blink and car won't start. I have to put a battery charger on the car just on 10 amps then car will start when I crank it. This is very annoying. Factory computer would have started under these same conditions. I have a...

Has anyone come up with a good solution to add an auxilary positive terminal under the hood. I want to get all these added on and "hotwire" circuits off the alternator and get the wiring off the engine. Most of the things I have found on summit or just in general have bad reviews, or they...

Have XFI 2.0 from Hartline running a caspers adapter harness. Been on the car for 3 years now, had the idle and part throttle tune set for 3 years now haven't needed to make any changes. Replaced alternator (wasn't having any problems, stud came loose while working on wiring, opened up to...

I am still running the factory cam sensor (probably 1987 oem), with no issues on my xfi. I bought a spare awhile back since sometimes they can be hard to find. But I am thinking about the long term is their any alternative to this expensive sensor while using stock accessories?

On my XFI the football doesn't track correctly the rpm and map. It is hovering over a higher rpm and map than is being reported. It is doing this on both data logs and live. I am going to attach a screen shot. On the datalog the gray line showing the path corresponds correctly with the...

Stock maf no problems just no longer need. One screen removed. $75 shipped SOLD

For sale: powerlogger, SD2 chip 1.2 (60lb injectors but you can run any injector size you want), delphi 3 bar map, Julio's map harness (let you plug and play with the TPS to pickup clean power without having to cut the harness). All part are working with no problems just going different...

I just switched to SD2 chip. I noticed that when I turn on the AC the radiator fan does not come on. I get the check mark for the AC on the power logger but it does not check the box for the fan. The fan does not run. The fan will run when the coolant temp reaches the set point. Once the...

SOLD The trans is still shrink wrapped to the pallet after receiving it back from Lonnie. He rebuilt it under warranty but I never installed it. I rebuilt my original trans myself instead. Billet anchor pin EA Super Pump™ Tensioned Teflon sealing rings 3 clutch OD Tested and sealed...

Thrasher stock injectors pump gas - plastic holder is broke but the pins on the chip are not damaged. Kenne Bell stock injector pump gas Joe Lubrant stock injector 110 Race gas $25 shipped for all three.

doing my trans rebuild I did not use any of the pump parts because I purchase a rebuilt pump from ck. From reading the directions 2 out of these three springs go internal to the pump. I have one spring left over that I don't know where it goes. Due to daily driver vehicle problems I have...

I am performing a mostly stock rebuild on my BRF 2004r. I am trying to minimize the billet parts and the expense. I need some advice if this is too much wear on the forward clutch housing My direct clutch drum has wear on the ID from the sealing rings and needs to be replaced. Where is...

87 TR with factory floor shifter. Had 0 issues with the shifter, replaced the transmission and now have problem. With the column linkage disconnected I can easily shift the car into every gear. With the column linkage attached and adjusted so that park & neutral are correct and the reverse...

I am troubleshooting my new trans shifting poorly, I have the pan down and measuring the TV plunger. With my old cable the measurements come out wrong from what lonnie recommends so I am trying to buy another cable so I can install and measure. I am a week into this trying to find a cable that...

Does anyone know of a source for the 11 tooth drive gear? If not is there another combination that works for the stock GN setup, (3.24 gears stock tire height)? Thanks Scott

I took pictures of everything before I removed the dash, but my phone died before I transferred them. I was able to get everything back together and just have these three left. File 0488 - Purple w White male single blade connector. Comes out of the main harness bundle from the fuse pannel...

Sorry about the bad picture. It is a single terminal connector that run down below the wiper motor. Thanks

I have my dash cluster loose but I am unable to remove it because of the wiring for the factory tach and boost gauge, it is soldered directly to the cluster. The wires run back into the dash but I cannot find a connector. How do i disconnect that wiring? Thanks

This is part III in my series of asking question about the Texas vehicle buying and selling process. I sold a car friday, I already went on the state website and filed the form to notify that the vehicle has been sold. I kept my license plates, is their anyway I can cancel those and get some...

Guys I need help with how to purchase a vehicle from a private party in Texas. I tried to buy a suburban Friday from an ad on craiglist. The truck was 5 minutes away so I went over to look at it. The seller had a title in his name everything looked good, but he said he did not have the "other...