Recent content by Tyler Stipe

  1. T

    Holley Harness (or similar) for G-body anyone?

    I know this is an old thread but I’m changing the routing of my Holley harness; is the flat horizontal part where you put the hole in the firewall? And what size hole did you make? Thinking about 2 1/8”. Thanks!
  2. T

    new to powerlogger- autometer wideband compatible?

    I'd like to chime in and ask a question about this, I just received a 6.1 TT chip, set for "Autometer", my gauge does not have buttons or adjustable settings. According to the Turbo Tweak install instructions, I'm supposed to adjust the BGD range to 0v=10 and 4v=18, but the settings for this...
  3. T

    Powerlogger File Review Please

    Thanks for the input, that's what I need. I'm waiting on the billet vacuum block, and I'll cut out any unnecessary lines, get all the Leakes fixed. As for pulling the timing out of the chip, how do I do that? I have the power logger, scan master g (with bluetooth to my tablet), and I have my...
  4. T

    Powerlogger File Review Please

    That's the kind of advice I need, I'll get some vacant and open stretch of road and see what it does, and of course, the base/idle numbers don't affect WOT, I just want to make sure my baseline numbers are good, so far I'm waiting on a new billet vacuum block, I adjusted the fuel pressure to...
  5. T

    Powerlogger File Review Please

    I forgot to mention, the previous owner removed the EGR setup, had the heads filled with aluminum and the intake has had the EGR cut out and filled in.
  6. T

    Hood mounting holes stripped....

    The 2 front bolt holes, on the hood mount, allow the bolts to just slide right in, without catching, so the hood just has the rear two bolts holding it in. After searching google and the forums for what the bolts thread into, I've had no luck, so I'm curious if they use speed nuts, or if...
  7. T

    Powerlogger File Review Please

    Now, the only issue I have about WOT right now, is I blew the last 2 head gaskets (right after installing them), by doing a couple WOT runs on the freeway, so I'm a little hesitant. I want to make sure my baseline numbers are at least good, before I start breaking things again.
  8. T

    Powerlogger File Review Please

    I'll have to see about connecting the boost to the Powerlogger.
  9. T

    Powerlogger File Review Please

    I checked around, found the vacuum block had a nipple snapped/cracked and loose. I'm going to order one of those billet vacuum blocks, but in the meantime, I used some silicon sealer in there. BLM is lower, but still not 128. Thanks for the tip!
  10. T

    Powerlogger File Review Please

    I'll try to be as brief as possible. Just bought this car a few months ago, the drivers head gasket ended up chirping and getting worse (pretty sure it was on its way out when I got the car), I replaced the head gaskets, the intake air temp sensor was bad, but I didnt realize it right away...
  11. T

    Getting KR on very slight deceleration as well as with Boost.

    I've searched all over for ideas and answers on fixing my KR. Cruising it seems just fine, but if I just barely let off the gas, it seems to get some KR, but if I fully let off the gas it jumps to 0 KR. Also, during boost, I'm getting some serious amounts of KR. I'm running 93 octane with...
  12. T

    1987 Buick Grand National Stolen

    Oh I had it Friday at 1pm, Saturday and Sunday. Was a fun weekend, I guess. Haha
  13. T

    1987 Buick Grand National Stolen

    Fayetteville, I don't think the seller took it. But you never know. Thanks!
  14. T

    1987 Buick Grand National Stolen

    Good afternoon all, My newly bought 1987 Buick Grand National was stolen Sunday night (16 April 2017) from Melvindale MI (south east Michigan, near Detroit), after purchasing the vehicle out of state in North Carolina on 14 Apr 2017. VIN: 1G4GJ1175HP464137 Car has a 4 point roll cage in...
Top