Recent content by oc192

  1. O

    Need help with FPR

    you are right, I have the line connected to the middle size line. I assumed the large line was feed, the middle line return, and the smallest line was the vent. :oops:
  2. O

    Need help with FPR

    Hello All, here is a quick update. I ran a -6 return and now the pressure is over 100!! When I turn the key on to just prime the pump, it jumps up to 80 instantly, then on to 100 when running. I put another fuel gauge on the rail just to make sure the gauge isn't wacked, getting the same...
  3. O

    Need help with FPR

    Hello All, I need some help diagnosing a fuel pressure issue. My current walbro fuel pump and accufab FPR are about 8 years old. My fuel pressure was set to 43 line off and everything seemed to run as expected however the pressure would bleed off to 0 in just a few seconds after shutting the...
  4. O

    fuel line routing

    ok thanks, just so we are on the same page... The feed line comes from the tank, goes thru the fuel filter and runs along the driver side frame rail and then it crosses over by the motor and connects to the passenger side fuel rail? Thanks
  5. O

    fuel line routing

    Hello All, I have a dumb question about how the fuel lines are routed. As I understand it, the feed line from the tank connects to the passenger side of the fuel rail and the return line to the tank connects on the driver side at the regulator. Which line runs through the fuel filter, the...
  6. O

    Racing in overdrive??

    Hello All, my car is pretty mild as I just have a pte 6266, 3000 stall, 110 race gas and drag radials. When I have a potential race on the street, I just leave it in OD and let her rip. I never really thought much about it because it will downshift when needed when roll racing and it will go...
  7. O

    Rear main seal and crank

    Thanks for the advice, I will pass this suggestion along when I have it replaced again.
  8. O

    Rear main seal and crank

    Hello All, I have owned my car for about 5 years now and it was completely stock when I bought it. Shortly after, I had the rear main seal replaced. The mechanic showed me the main bearing cap and it had some wear marks on it. After about a year or so, the rear main started leaking again so...
  9. O

    Racing events in AZ

    Hello All, haven't been on the board in quite awhile. They use to have a Buick racing event around Thanksgiving time at the now defunct track out by Surprise. Is there a similar event now at Wild Horse or did that event get scrubbed entirely?
  10. O

    Brad Penn Oil

    Just wondering if there is enough zinc in this oil to keep the cam happy or does it still require ZDDP additive? Thanks
  11. O

    frame bent/rolled in up front causing alignment problems?

    Hello Charlie, this is the sheet from the original alignment....
  12. O

    frame bent/rolled in up front causing alignment problems?

    Thanks Pacecar and Chuck.... DO you think an extra 1/2 inch on both sides will get the caster in the 4 range? Also are you referring to these? http://www.speedwaymotors.com/Chromoly-Upper-Control-Arm-Steel-Cross-Shaft,5584.html
  13. O

    frame bent/rolled in up front causing alignment problems?

    Thanks Steve.... anyone else heard of this? Assuming the frame is not the issue, what would prevent these guys from properly aligning my car.... especially the castor?
  14. O

    frame bent/rolled in up front causing alignment problems?

    Hello All, I recently upgraded my front suspension with Moog parts and gbody uppers/lowers. After the upgrade I went to a shop to have the front end aligned. Tech advised he could not get the car into spec. The castor is way out of spec, one side is -1.3 and the other side is 0.0 So...
  15. O

    Also looking for stock intercooler with dutt neck

    Thanks to everyone who replied! sent payment to trashmech, looking forward to getting her bolted on.... Thanks Mike!
Top