Search results

  1. T

    N20 nozzle and alky nozzle placement

    Thanks for the clarification Mr spool
  2. T

    N20 nozzle and alky nozzle placement

    That's what I thought on the location. Doesn't the nozzle usually face the throttle body? Or do you face it into the air stream in this situation?
  3. T

    N20 nozzle and alky nozzle placement

    Guys that run nitrous and alky, where are you mounting your nitrous nozzle. Before the alky nozzle? After that alky nozzle? In the plenum? Wet or dry kit?
  4. T

    D5 Orange stripe

    using the tach on the scanmaster, stalling 2450rpm with a gt6152. I have put about 10,000 miles on it. Not sure how many the previous owner put on it. Not sure what these are going for nowadays. Any fair offer takes it.
  5. T

    WTB 3000-3200 Lock up convertor

    For the 200r4. Something that is in decent shape.
  6. T

    pitt july meet

    Maybe Ill come out. Been having some health issues and trying to limit what I do and eat. See how I feel in the morning.
  7. T

    Wtb: Turbocharger Core. Hot Air or Cold Air 1984 - 1987

    I have a stocker from IC car. unknown milage. Minimal up and down play. Alot of in and out. No fin contact, still made 25 psi and pulled hard. It just smoked pretty good. 1 bolt hole in the out return will need a heli coil. $125 shipped. no actuator.
  8. T

    Acadia or Enclave?

    The software sometimes fixes the issue unless the chains are stretched too far. They aren't bad once you do 2 or 3. Drop the whole motor/trans/cradle and all. Pull up a chair and go to town.
  9. T

    Acadia or Enclave?

    Mechanically they are the same. We sell alot of them and people seem to like them. I have done about a dozen timing chains because they stretch from lack of regular oil changes and then cause a check engine light. 3-5-R wave plates breaking, power steering clunks, whine, and sqeaks, and...
  10. T

    Attention pittsburghers

    SWPA Motorsports - View topic - Race Gas
  11. T

    Good stock turbo

    Tim, I got a stock turbo on my car. Its spools and pulls hard. Minimal shaft play, however its starting to smoke and there is some oil getting into the cold side. Its going to need seals sooner or later. Let me know if interested, I'm looking for something a little bigger if you got...
  12. T

    Stock Driveshaft Cut 1 icnh

    Stock Driveshaft I had it cut 1 inch, rebalanced and painted about 5 years ago to use when i swapped over to a th400. when i switch over to a th400 and have gone less that 500 miles since then. Maybe 20 mid 11 seconds passes since then also. Comes with a good 1330 joint on one end and a 1330...
  13. T

    RJC Power Plates

    I'll take the one for the accufab doghouse. Take paypal?
  14. T

    99 Chevy Truck Help!

    those trucks will still run on 35psi or so of fuel pressure when spec is 60psi ish. check fuel pressure and fuel trim and go from there.
  15. T

    Pittsburg area

    hmm i can't say i do know any of those guys. I may reconize their cars but i don't know any of them
  16. T

    Pittsburg area

    I am in the northern area of pittsburgh, i think stagemonster is out eastward? I can look at it if you want. I have two TR's one now a turbo sbc car. All built by me. I have been around these cars for 10 years now and am a ASE master tech. let me know if interested.
  17. T

    Proudly say what you do for a living!

    ASE master tech at a chevy dealer 9 years and counting. I also run a tow truck for a local company here and there for some extra cash.
  18. T

    Flashlight Drags

    Hey Justin. That T-type at the end was me. I didn't get to talk to you but your car is sharp.
  19. T

    Westrn Pa Summer meets!!!!

    I just picked up another TR. I work less than a mile from this cruise. if it is not raining i will be down.
  20. T

    Westrn Pa Summer meets!!!!

    North hills area. We have met a few times stagemonster. I am also on pittspeed.
Top