Search results

I just converted over to vacumm brakes and updated the recalled proportioning valve. I know I'm supposed to have to compress the valve on the end of it but it already seems to be maxed out and wont go in. I'm using a c clamp to try and compress it...On my old one, nothing happened either.. But...

I am in the process of upgrading my axles and carrier to 30 spline and was wondering what Rear you all suggenst.. Eaton Posi Detriot TrueTrac Detroit Locker Powertrax locker I"m leaning towards the TrueTrac because of smoothness. Ive had lockers in my 4x4 before so Im familiar with how they act...

I was wondering what some of your opinions would be if it is cheaper to rebuild my stock 200 to say handle say 550 HP and beet on it or buy and built one from one of our vendors? Nothing wrong with mine yet I just would like to deal with the issue of it while its out on the bench. Thanks for...

I have a new set of forged pistons and moly rings for sale. Just don't need these for my build. Im asking $425+shipping. Parts are in Washington. Hastings Moly Rings 2m-5612-.030 Part # TA1635-.030 Speed Pro Forged Pistons L2481F .030 Skirt size 3.82675...

I wanted to know who makes the best 3" DP. integrated waste-gate. Fit, finish, performance wise. I'm sure they all are good some got to be better then others.

I was just curious if anyone on here was running one of the 9" bolt in kits they sell. They are the cheapest I can find. Seemed like a decent company on the phone.

I was wondering what all needed to be done if you flattened a cam lobe? Obviously tear down and inspect bearings and such but do you usually have something else done if everything looks OK? thanks for the help.

As the title says I am up for suggestions on who I should send my GNs motor off to. I live in Alaska and just haven't come across anyone that I really trust to build my engine:frown: so I'm looking to be shipping it off to the lower 48. Hopefully somewhere on the west coast. Thanks for your help.

I was wondering if there is a difference in the PTC 10"L/U torque converters that Gbody sells and F.T. sells besides $$$? Do they have them set up differently? Thanks for your input.

I really want to order one of these kits and was just curious if anyone is having any issues with these kits at all. Thanks for the help

I was thinking of ordering a cam kit from Full Throttle and was wondering if anyone has had any problems with the cams, lifters, etc or installing them. This is going to be the second time for a cam swap. Flatten old one in less then a 1000 MILES. :mad: Im open for suggestions on which cam I...

Does anyone sell a 2 5/8 twin gauge pod for g body. Or even a single one anymore?

Anyone know where I can find all the brackets I need to put a a 9in in the car? I just pick one up and was looking to do the swap.

I can't seem to get anything less than around 15psi w/the controller. WG almost all the way out, the controller only is turned about 1 turn from being all the way out. have everything hooked accourding to drawings. Any Ideas. the turbo is either a ta60 or a te44.

My fuel pressure is set at 42 w/ vacumm line off. WHen installled it drops to about 36. while I was driving and boost comes on it quickly jumps to 50 1st,2nd, drops to around 48. while in 3rd. Is this something that usually happenes? I have 36lbs inj. hot wire kit, new fuel filter. THe pump is...

My 8.5 houseing is bent pretty bad to where the tires wear out on the insides around 7500 miles. I was wondering what the right width of rearend I should be looking for? Is there certain years of a rear I should look for? and where could I get the brackets to do the swap? If I wanted to get a...

my scanmaster mph reading about half of what my speedo is. What is causing this? Is it hurting my performance or driveability any?

my mph reading on the scan master is about half of what the speedo is reading. Whats causing this? Is this hurting my performance or driveability any?.

I was just wondering if there is anything special I need to do when I change out the TC and my hardened stator shaft. Is it just a quick bolt on?

I was just wondering if anyone has run the a ACC performance Boss Hog torque converter? I have one laying around and don't know if its worth my time to swap it out for the stock D5 or not? I bought it from Postons a couple of years ago and never got around to putting it in. ITs the 2200-2800.